Lennox RHAP54N Скачать руководство пользователя страница 16

Страница: 16 / 40

NOTE: DIAGRAMS AND ILLUSTRATIONS ARE REPRESENTATIVE AND ARE NOT DRAWN TO SCALE.

www.LennoxHearthProducts.com

VENT RESTRICTOR

REqUIREMENTS

Installation of the provided vent restrictor as-

sembly is required for the venting configura-

tions listed in Figure 16-2.

The Vent Restrictor Kit (provided with the

fireplace; see Figure 16-1) includes one vent

restrictor base, two wings, and four screws.

1. Refer to Figure 16-2.
For venting configurations listed under

“Setting 1”:
Use the vent restrictor base only

(no assembly is required).

For venting configurations listed under

"Setting 2" or "Setting 3":
Use the four provided screws to attach

the two wings to the vent restrictor

base in the applicable position.

2. If the baffle and back panel are already

installed, remove them before proceeding.

See Page 26.

3. Install the vent restrictor assembly from

inside the firebox. With the

flaps

on the

vent restrictor base facing UP, carefully

bend the flaps inward just enough to slide

the assembly up into the vent collar, as

shown in Figure 16-3).

The vent restrictor is held in place by fric-

tion only.

The entire vent restrictor assembly must be

up inside the vent collar, with no portion

showing inside the firebox.

Vent Restrictor kit

(provided with fireplace)

(1) Vent Restrictor Base

(2) Wings

(4) Screws

Figure 16-1

“flaps”

Figure 16-2

Setting 1 (Vent Restrictor Base only) is required for the following configurations:
• Horizontal termination with total vertical run of more than 6 ft.
• Vertical termination with total vertical run of 6–10 ft.

Setting 2 is required for the following configuration:
• Vertical termination with total vertical run of 10

+–40 ft.

Setting 3 is required for the following configuration:
• Vertical termination with total vertical run of 40

+–60 ft.

Figure 16-3: Vent Restrictor Installation

[DETAIL]

Vent

Collar

firebox

Vent Restrictor Assembly Settings and Applications

Vent

Restrictor

Assembly

(held in place

by friction only)

LENNOX HEARTH PRODUCTS • RHAPSODY™ LINEAR DIRECT-VENT GAS FIREPLACES (MODEL RHAP54N) • INSTALLATION INSTRUCTIONS

VENTINg INSTALLATION

(CONTINUEd)

Содержание RHAP54N









































Результаты поиска

Содержание RHAP54N

Отзывы:

Похожие инструкции для RHAP54N

Бренды по названию

Популярные бренды

Lennox RHAP54N, Руководство по установке

Результаты поиска

Содержание RHAP54N

Отзывы:

Похожие инструкции для RHAP54N

Бренды по названию

Популярные бренды