Lennox Harmony III Скачать руководство пользователя страница 13

Страница: 13 / 80

1.10.9.

System Configuration/E-Heat Stages)

The SYSTEM configuration jumpers must be inserted to select the type of cooling

and heating system that has been installed and the E-HEAT Stages jumper defines

if the system is dual fuel or defines the number of electric heating stages used.

1.10.9.1. Gas Furnace and Air Conditioning

For a gas furnace and air conditioning

combinations, put the jumper on

GAS (as shown) and select the

number of equipment cooling stages

by placing the cooling jumper to the

appropriate site (place on 1COOL for

1stage cooling or 2COOL for 2-stage

cooling).

SYSTEM

Configuration

2COOL

2HP

GAS

1COOL

1HP

E-HEAT

Stages

IN A/C AND GAS FURNACE

CONFIGURATION, “HP”

AND “E-HEAT” JUMPERS

ARE IGNORED

In this configuration, the maximum discharge temperature (upper temperature limit)

at which the furnace is allowed to run is 160°F (except when 140F DAS jumper is in

place). At the upper limit, the zone control system removes any heat demand from

the furnace for a minimum of five minutes and until the temperature comes back

within normal operating temperatures.
While at or above the upper temperature limit, the control unit signals for continuous

blower operation to those zones from which a thermostat heat demand is received.

When setting up the furnace control board options, be sure to set the BLOWER-

OFF DELAY to no greater than 210 seconds.

1.10.9.2.

Heat Pump with Electric Backup Heat

For heat pump with electric backup

heat, select HP position as shown in

this diagram.

SYSTEM

Configuration

2COOL

2HP

GAS

1COOL

1HP

E-HEAT

Stages

In this configuration, the maximum discharge temperature the electric heat or heat

pump is allowed to run is 135°F. At that temperature, the zone control system

removes demand from the heating unit for a minimum of five minutes and until the

temperature returns to the normal operating temperature range. While at or above

135°F, the control unit signals for continuous blower operation to those zones from

which a thermostat heat demand is received.
Select the number of equipment cooling stages by placing the COOL stages jumper

to the appropriate side (1COOL or 2COOL). Similarly, set the number of Heat Pump

stages (1HP or 2HP). Jumper settings on the above diagram illustrate the proper

settings for a two stage heat pump and two-stage air conditioning system.

When using a heat pump with electric backup heat, insert an E-HEAT jumper to

select the total number of available electric heat stages. The diagram above shows

a single heat-strip configuration.

1.10.9.3. Heat Pump - Dual Fuel heating, 1-stage or 2 Stage Heat Pump and

Gas Furnace

This diagram shows a dual-fuel

configuration (heat pump for heat

and cool with gas backup heat).

SYSTEM

Configuration

2COOL

2HP

GAS

1COOL

1HP

E-HEAT

Stages

HP position must be jumpered for Dual Fuel applications and the E-Heat Stages

jumper must be set to “DF” for dual fuel operation.
Select the number of equipment cooling stages by placing the COOL stages

jumper to the appropriate side (1COOL or 2COOL). Similarly, set the number of

Heat Pump stages (1HP or 2HP). Jumper settings on the above diagram illustrate

the proper settings for a one stage heat pump and one stage of cooling.

1.11. Common System Component Wiring

Use thermostat wire to connect dampers, damper transformers, and the DAS

probe with the zone control system.

IMPORTANT

Avoid running any control wiring close to AC house wiring. If this cannot be

avoided, limit close parallel of power and control wiring to a few feet.

1.11.1. Dampers and Damper Transformer

Connect dampers to the zone control panel. A total of six dampers may be

connected at the damper output terminals on the zone control panel. If additional

dampers are used, additional transformers and relays will be needed.
Fuse F1 will protect the damper outputs from a short circuit or overload in the

damper wiring.
If dampers are applied to the return duct system, the dampers for each zone must

be wired in parallel. Connect damper transformer to zone control panel terminal

block.

Содержание Harmony III

















































































Результаты поиска

Содержание Harmony III

Отзывы:

Бренды по названию

Популярные бренды

Lennox Harmony III, Инструкция по установке, настройке и эксплуатации

Результаты поиска

Содержание Harmony III

Отзывы:

Бренды по названию

Популярные бренды