5
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Top Radiant
Panel
Top Bustle
Bottom
Bustle
Control
Compartment
Access Panel
Unit Parts Identification
Figure 4
Step 3.
Install the Vent System &
Exterior Termination -
In the United States, vent installation must
conform with local building codes. In the ab-
sence of local codes, vents must be installed in
accordance with the current edition of the
National Fuel Gas Code (ANSI-Z223.1).
In Canada, vent installation must conform
with local building codes. In the absence of
local codes, vents must be installed in ac-
cordance with the current edition of the Na-
tional Standard of Canada CAN/CGA-B149.1
or B149.2 Installation Code.
This gas fireplace must be vertically vented
using listed 6 in. type-B, double-walled vent
pipe and a listed vent termination.
If the appliance is to be elevated above floor
level, a solid continuous platform must be
constructed. Headers may be in direct contact
with the appliance top spacers but must not be
supported by them or notched to fit around
them. All construction above the appliance
must be self supporting,
DO NOT
use the
appliance for structural support.
Side Nailing Flanges
The fireplace should be secured to the framing at
the side(s) and/or rear of the unit using the
factory-provided nailing flanges. Install the nail-
ing flanges - 8 (EBVST), 4 (EBVPF, EBVCL,
EBVCR) - as shown in
Figure 5
using the existing
screws. Position the fireplace within the fram-
ing. When required, the flanges may be bent 90
degrees by hand or with the assistance of a
hammer. Use wood screws to secure the nailing
flanges to the framing.
See Table 2 on page 4
for
clearances of framing members to cabinet parts
in the nailing flange area. The nailing flange itself
is exempt from these clearances.
Step 2. ROUTING GAS LINE
Step 1.
(page 5) Construct the appliance
framing. Position the appliance within the
framing and secure with nailing brackets.
Step 2.
(page 5) Route gas supply line to
appliance location.
Step 3.
(page 5) Install the vent system
and exterior termination.
Step 4.
(page 10) Field Wiring
a.
Millivolt Appliances –
The operating con-
trol switch is factory installed.
b.
Electronic Appliances – Connect 120 Vac
electrical power to the appliance receptacle.
Step 5.
(page 11) Make connection to gas
supply.
Step 6.
(page 12) Outside Air Kit Installation
Step 7.
(page 13) Install the log set, ver-
miculite and glowing embers.
Step 8.
(page 13) Checkout appliance op-
eration.
Step 9.
(page 13) Install glass enclosure
panels.
Step 10.
(page 14) Burner Adjustment.
Step 11.
(page 14) Spillage Test and Safety
Limit Switch Operation.
Step 12.
(page 15) Install the hoods.
3
- Open the control compartment access
panel, by actuating the spring-loaded mag-
netic catches securing the panel, gently de-
pressing the outer top corners of the panel
until the catches "pop" the panel free and
allowing it to swing out and down to open.
See
Figure 20 on page 12.
4
- Open the latches (located on the left and
right sides of the unit front opening, under the
firebox floor) securing the glass enclosure panel.
Remove the panel by tilting it outward at the
bottom and lifting it up. Set the door aside
protecting it from inadvertent damage.
See
Figure 24
on page 13.
Step 1. FRAMING
Frame these appliances as illustrated in
Fig-
ures 8 (EBVST), 9 (EBVPF), 10 (EBVCL) or
11 (EBVCR) on pages 6 and 7
. All framing
details must allow for a minimum clearance
to combustible framing members as shown
in
Table 2 on page 4
.
Figure 5
DETAILED INSTALLATION STEPS
All appliances are factory-equipped with a flex-
ible gas line connector and
¹⁄₂
inch shutoff valve.
(See step 5 on page 11)
.
Route a
¹⁄₂
" (13 mm) gas line as shown in
Figures 8 (EBVST), 9 (EBVPF), 10 (EBVCL) or
11 (EBVCR) on pages 6 and 7
. Gas lines must
be routed, constructed and made of materials
that are in strict accordance with local codes
and regulations.
Turn tabs down and secure to the floor with
8d nails or other appropriate fasteners on all sides
of the unit which do not have viewing glass panels.
EBVST SHOWN
(EBVPF - NO NAILING FLANGES ON END WITH GLASS PANEL)
EBVCL SHOWN
(FOR EBVCR VIEW, INTERCHANGE SIDES)
Remove these two screws and use them
when installing the nailing flanges.
Nailing
Flanges
The appliance is shipped with all gas controls
and components installed and pre-wired.
1
- Remove the shipping carton.
2
- Remove the top radiant panel;
see Figure 4.
Floor Nailing Tabs
Secure the fireplace to the floor as shown in
Figure 5.
See the page numbers references in the follow-
ing steps for detailed procedures.
