2
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
Offset Venting
Vertical Venting
Figure 1
TABLE OF CONTENTS
Packaging ........................................ page
2
Introduction ..................................... page
2
General Information ......................... page
2
Massachusetts and New York
Requirements ................................ page
2
Location .......................................... page
4
Appliance and Vent Clearances ....... page
4
Vent Termination Clearances ........... page
4
Typical Installation Sequence .......... page
4
Detailed Installation Steps ............... page
5
Step 1. Framing ............................. page
5
Step 2. Routing Gas Line ............... page
5
Step 3. Install the Venting System . page
5
Fireplace Specifications ................... page
6
Step 4. Field Wiring ....................... page 10
Step 5. Connecting Gas Line .......... page 11
Step 6. Outside Air Kit Installation . page 12
Step 7. Installing Logs ................... page 13
Step 8. Checking Unit Operation ..... page 13
Step 9. Installing Glass Enclosure
Panels .......................................... page 13
Step 10. Burner Adjustment ............ page 14
Step 11. Spillage Test and Safety
Limit Switch Operation ................ page 14
Step 12. Hood Installation ............... page 15
Finishing Requirements ................... page 15
Cold Climate Insulation .................... page 15
Gas Conversion Kits .................. page 16
TYPICAL INSTALLATION
DO NOT ATTEMPT TO ALTER OR MODIFY
THE CONSTRUCTION OF THE APPLIANCE OR
ITS COMPONENTS. ANY MODIFICATION OR
ALTERATION MAY VOID THE WARRANTY,
CERTIFICATION AND LISTINGS OF THIS UNIT.
Note:
Installation and repair should be per-
formed by a qualified service person. The appli-
ance should be inspected annually by a quali-
fied professional service technician. More fre-
quent inspections and cleanings may be re-
quired due to excessive lint from carpeting,
bedding material, etc. It is imperative that the
control compartment, burners and circulating
air passage ways of the appliance be kept clean.
This installation manual will help you achieve a
safe, efficient and dependable installation for
your appliance and vent system.
Please read and understand these
instructions before beginning your
installation.
GENERAL INFORMATION
PACKAGING
The assembled vented gas fireplace is pack-
aged with:
1 - one log set located within the firebox.
2 - one plastic bag containing the literature
package, which consists of the homeowner's
manual, installation instructions, log place-
ment guide and warranty, 8 (EBVST), 4
(EBVPF, EBVCL and EBVCR) nailing flanges;
plastic bag is located on top of the fireplace.
3 - two hoods (EBVST, EBVCR, EBVCL), or
three hoods (EBVPF) taped to the top of the
fireplace.
4 - one plastic bag of glowing embers, one
plastic bag of decorative volcanic stone and
one bag of vermiculate is located in the
bottom compartment.
INTRODUCTION
These vented gas fireplaces are designed for
residential applications. They must be installed
with approved type-B, 6 in. double wall vent
pipe systems routed to the outside atmosphere.
The millivolt appliances are designed to operate
on either natural or propane gas. A millivolt gas
control valve with piezo ignition system provides
safe, efficient operation. If any optional accesso-
ries which require electrical power are being
installed, the electrical power must be provided
at the time of appliance installation.
Electronic appliances are designed to operate
on natural or propane gas. An electronic inter-
mittent pilot ignition system provides safe,
efficient operation. External electrical power is
required to operate these units.
These appliances comply with National Safety
Standards and are tested and listed by Omni-
Test Laboratories (Report No. 116-F-07A-5) to
ANSI Z21.50 - 2003 (in Canada, CSA 2.22 -
2003), and CAN/CGA-2.17-M91 in both USA
and Canada, as vented gas fireplaces.
These appliances may be used for bedroom
installations in the United States and are
listed accordingly. These units may not be
installed in bedrooms in Canada.
Installation must conform to local codes. In the
absence of local codes, installation must com-
ply with the current National Fuel Gas Code,
ANSI Z223.1. (In Canada, the current CAN-1
B149 installation code.) Electrical wiring must
comply with the National Electrical Code ANSI/
NFPA 70 - (latest edition). (In Canada, the
current CSA C22-1 Canadian Electrical Code.)
WARNING: THESE FIREPLACES ARE
VENTED DECORATIVE GAS APPLIANCES.
DO NOT BURN WOOD OR OTHER MATE-
RIAL IN THESE APPLIANCES.
Massachusetts And New York City, NY
Requirements
These appliances are approved for installation
in the following USA locations listed in the
following:
Massachusetts:
Installation of these fireplaces are approved
for installation in the US state of Massachu-
setts if the following additional requirements
are met-
• Installation and repair must be done by a
plumber or gas fitter licensed in the Common-
wealth of Massachusetts.
• The flexible gas line connector used shall not
exceed 36 inches (92 centimeters) in length.
• The individual manual shut-off must be a T-
handle type valve.
New York City, NY:
Installation of these fireplaces are approved
for installation in New Your City in the US state
of New York, if the following additional re-
quirements are met-
• An outside air kit (FOAK-4 or FOAK-4LD)
must be installed.
