Leitronic AG EA-8-WRL868, Инструкция по использованию

Страница: 18 / 40

18
6.4 Supervision mode
6.4.1 LED indication
In active supervision mode , the LED is flashing every 4 seconds. The LED is also lit, if the acoustical
monitoring is activated and the selected noise level is reached.
LED: acoustical monitoring inactive
LED: acoustical monitoring activated
LED: inactive mode
6.5 Alarm release
6.5.1 ..independent from state of arming (armed / disarmed)
Active by Factory set
alarm cause
1)
I II III
Entry delay Alarm
connection
Announce the alarm cause
Panic
  
Instantaneously Listening-in “Emergency call activated”
Emergency
2)
  
Delayed Hands-free “Emergency call activated”
Smoke
  
Delayed Hands free “Alarm due to fire zone n ”
Technical detect.
  
Delayed Hands free “Alarm due to technical detector, zone n”
24h
  
Instantaneously Listening-in “Alarm due to zone n”
1. Factory setting cause of alarm (user specific changes not mentioned)
2. An emergency call will be triggered, if the button has been activated for one second. After a pre alarm
period of 20 seconds the text “emergency call activated” is announced. A pre warning announcement is
used to avoid false alarms (i.e. technical error like power failure, unwanted emergency calls). During the
pre warning period the alarm can be cancelled by pressing the emergency button respectively by pressing
key
0 . or telecommand (arm/disarm)
6.5.2 ..if system is armed only
Active by Factory set
alarm cause
1)
I II III
Entry delay Alarm
connection
Announce the alarm cause
Intern
  
Instantaneously Listening-in
Entry/Exit
  
Delay Listening-in
Extern
  
Instantaneously Listening-in
“Alarm due to zone n”
Noise
  
Instantaneously Listening-in “Alarm due to noise ”
Sensor 1
2)
  
Instantaneously Listening-in “Alarm due to sensor 1 ”
Sensor 2
3)
  
Instantaneously Listening-in “Alarm due to sensor 2 ”
Power failure
4)
  
Delay 1 min. Hands-free “Alarm due to power failure ”
1. Factory setting causes of alarm (user specific changes not mentioned)
2. Sensor 1 can also be used as a presence verification sensor (

section 6.5.5)
3. Sensor 2 can be enabled according to section 10.2.3.2
4.
EasyAlarm®
monitors mains voltage and triggers an alarm if power loss is longer than 10 to 20 minutes
(time-out according to section 9.4). The mains power monitoring does not start if after power up the mains
power is not detected. In this case the message „power failure“ will be announced. After any mains power
detection
EasyAlarm®
automatically start power monitoring.
6.5.2.1 New alarm release
After an alarm
EasyAlarm®
remains inactive during a waiting period of two minutes. Only if at expiration of
this waiting period an alarm event (wired sensor or wireless contact) occurs again, a new alarm is released.
Note:

After an alarms through sensor-1/2 or a wireless contact the sensor MUST return to its rest condition before
a new alarm can be triggered.
6.5.3 ..due to status report check (wireless sensors 0..6)
Wireless sensors with sensor function 0..6 are sending their status (battery condition/alarm condition/tamper)
every 65 minutes. If this status report is missing for more than 10 hours (due to battery low, out of range …)
EasyAlarm
®
will proceed as follows:

System is disarmed: Announcement “detector malfunction, zone n ” every 10 minutes

System is armed: 1 minute before an alarm is triggered there is an announcement “alarm due
to detector malfunction, zone
n ”. After this period
EasyAlarm
®
dials the
alarm-number(s) and establishes a hands-free connection.
Noise Nois
4 seconds 4 seconds 4 seconds 4 seconds