Figure B2: Positions of the key in the battery lock
Similar to a car ignition lock, there are 3 positions
Position 1: Remove battery.
All the way anti‐clock‐wise. Battery
is OFF and can be removed. Push key IN when turning towards
position 2.
Position 2: OFF.
Battery locked into frame. Push key IN when
turning anti‐clockwise to Position 1.
Position 3: ON .
All the way clock‐wise. Battery locked into frame.
Position 1
(Remove)
Position 2 (OFF)
Position 3 (ON)
Functions of battery & lock (insert key and turn)
Charge display
White button
Lock bolt
protruding through
opening in battery
rail
Battery rail
Key
.
Figure B1. A correctly installed battery is shown. To install
battery, put key in position 1 (Figure B2), insert rail along
grooves on side of battery and slide battery all the way down.
Before you turn the keys ensure the lock bolt of the battery lock
is aligned correctly with the opening in the battery rail. Push the
battery down or lift the battery up to align the bolt with the
opening. If the battery is not aligned correctly, the bolt will hit the
battery rail and you can’t turn the key. The bolt won’t be able to
fit through the opening on the battery rail. If battery rattles
during
ride,
tighten
screw
holding
rail
to
frame.
Checking battery charge:
Battery needs to be in the "ON" position (3) when pushing and
holding the white button on top (Figure B1) to check battery
charge (2 green lights, 1 red light: full. 1 green light, 1 red light:
battery 2/3 full. red light only: charge battery soon (1/3 charged).
CAUTION!
PUSH THE KEY INTO THE LOCK GENTLY when turning between positions 1 and 2! When turning between Position 2
and Position 3 DON’T push the key into the lock, just turn normally. Don’t switch off the battery while riding. Only switch it off
when bike is standing still
.
CAUTION!
Brand new batteries may take a sharp tug to be removed from the rail. First unlock battery (Position 1) and make
sure that the Lock bolt has retracted fully and that the opening in battery rail is clear (Figure B1). Then hold the bike with one
hand, hold the battery handle (Figure B1) with the other hand and give it a sharp tug. Be careful not to hurt yourself.
Battery handle
4
5
6
7
8
9
Battery
Charger
Figure B3: Charging the battery (Illustration)
Connect the
power cord (5)
firmly to the
power socket on the charger (6).
Gently rotate
round black cover on battery (9)
to expose
battery input socket
(8).
Then connect the
charger output cable (7)
to the
battery input socket (8)
on the battery. The LAST step is to connect the
power chord (5)
to the
wall
power
point
(AC,
110/220
Volt,
50/60Hz)
(4).
WARNING
! To prevent electric shock connect
power cord (5)
to
wall socket (4)
as LAST step. Do not open charger. Voltage is detected automatically. Do not
yank cables. Pull on plugs, not on cables.
Charging the battery
•
The battery can be charged on or off the bike.
•
Charging temperature between 10
℃
(50 °F ) and 30
℃
(86 °F).
•
During charging the temperature may increase to about 50
℃
(122 °F).
•
Stop charging battery if it gets unusually hot and contact customer
service. Charge undercover in dry area.
•
Only use original supplied charger to avoid overheating, bursting or
ignition.
•
The chargers are smart chargers, which means they will automatically
stop charging when the battery is full.
•
The battery takes about 5‐7 hours to charge if It’s completely discharged.
•
At first charge, it can take longer since battery pack is balancing.
•
If battery does not fully charge within 8 hours, disconnect charger and
contact customer service.
•
If it’s not fully discharged it will take less time to charge.
•
It is recommended to switch the battery OFF while charging.
•
Disconnect charger after charging. Unplug charger from electricity grid if
not in use.
BATTERY:
Installation and using the keys
Lights on Charger:
•
If there are TWO LIGHTS on the
charger. BOTH LIGHTS RED: Charging.
ONE LIGHT GREEN and ONE LIGHT RED:
Fully charged or not connected.
•
If there is ONE LIGHT on the charger:
RED: Charging. GREEN: Fully charged.
WARNING!
The charger can get very hot
while charging. Always keep it away from
material which can catch fire. Do not cover
charger. If there are any signs of smell,
smoke or melted plastic or unusual noises,
immediately disconnect charger from power
socket and do not use charger again. Always
attend charger during charging. Keep away
from water, moisture, children and pets.
Follow instructions contained on the label of
the charger.
20
© Leitner Pty Ltd 2019
Содержание Berlin 2020
Страница 25: ...25 Leitner Pty Ltd 2019 ...
