Leitner Berlin 2020 Скачать руководство пользователя | Manualshive

Страница: 9 / 25

background image

Figure FS3:

View from front: Fasten all

bolts which hold handle‐bar (4 bolts
shown in picture) to 18 Nm

Quick release Nut

4) Use quick release Lever to adjust
stem height. Close firmly before
riding.

Upper steerer‐clamp bolts
(18‐20Nm)

Bolt at centre (may be
covered by rubber cap
which can be removed)

Safety latch
securing folding
quick release lever

Folding quick
release lever
In upright
position (15 Nm)

Hinge bolt

Lower steerer
clamp bolts (18‐
20 Nm)

1) While pulling quick release
lever down, carefully

fold stem

UP until it’s fully closed

Folded stem, view from TOP.

Centre bolt attaches stem to fork

Bolt anchoring stem height
adjustment wire

Quick‐release nut

Safety latch

safety
clamps

Figure FS4

3) Secure quick‐release with safety latch.

2) Ensure safety clamps are closed,
move quick release lever into an
upright position.

The handle‐bar and stem

are used to steer the bike. The handle‐stem connects to the fork. Some stems can

be adjusted in height to provide a comfortable riding position.

SuperT: Straightening and folding the handle‐stem

:

The stem is folded to the right side of

bike. Un‐fold it and secure it using quick‐release levers. Bolts should be tightened to 9‐10 Nm unless specified otherwise.
Make sure all bolts are tight and that there is no excess play in the stem. The stem sits at an angle to the bike frame, about
45 degrees. This is normal and will allow the handle‐bar to be folded in a parallel way to the bike.

To align stem with wheel,

walk to front of bike, put wheel between your legs, open

quick release lever and centre stem (Figure FS2). Only minor adjustments can be
made using the quick‐release lever (Firgure FS1). If major centering adjustments
are needed, release steerer‐clamp bolts (Figure FS1) by a few turns, centre stem,
then tighten bolts to 18‐20 Nm.

CAUTION!

: The folding stem should fold to the right side of the bike. The handle‐

bar should be approximately parallel to the bike frame when fully folded. Fold
carefully. Take care not to damage the bike during the folding procedure. Make
sure to leave enough slack for all wires to avoid damaging wires while folding.

CAUTION!:

Pinching hazard. Keep clear of moving parts.

Figure FS1

Figure FS2

9

Quick‐release lever

© Leitner Pty Ltd 2019

«
...
7
8
9
10
11
...
»

Содержание Berlin 2020


























Отзывы:

Нет отзывов

Похожие инструкции для Berlin 2020

Бренд: XPRIT Страницы: 16

Бренд: baby joy Страницы: 11

Бренд: Volter Страницы: 35

Бренд: URBANGLIDE Страницы: 52

DORSODURO 750 ABS 2015

Бренд: APRILIA Страницы: 146

Бренд: CAMSO Страницы: 51

Бренд: solowheel Страницы: 21

Бренд: Tern Страницы: 76

Бренд: Marzocchi Страницы: 23

Rocket ACIS99ROCKTBLU

Бренд: InStep Страницы: 18

Бренд: RAMBO Страницы: 25

Speedmax CF SLX

Бренд: Canyon Страницы: 33

Бренд: Acros Страницы: 2

Бренд: Nihola Страницы: 4

Бренд: LOVENS Страницы: 12

Бренд: LOVENS Страницы: 16

Бренд: Optibike Страницы: 12

Бренд: Sun Microsystems Страницы: 27

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды