LEHNER POLARO E Скачать руководство пользователя

Страница: 10 / 48

1 What you should know

1.7 About your safety

•

Carefully read and observe these operating instructions before use.

Always keep this manual to hand at the point of use.

•

Observe the accident prevention regulations, safety and operating

regulations and the regulations for environmental protection.

•

Observe all applicable standards and guidelines.

•

Observe the safety instructions.

•

Before operation, check that the hopper is correctly seated in its

mounting and that the spreader is safely and correctly attached to the

carrier vehicle.

•

Do not operate the spreader if there are technical safety defects.

•

Immediately resolve any safety-related defects.

• When travelling on public roads and streets, observe the road traffic

regulations.

•

There must be no other persons in the spreading zone.

•

Switch off the motor before troubleshooting.

•

Disconnect the electrical power supply for maintenance work.

•

Never open the hopper when the agitator is running.

•

Do not reach into the hopper during operation.

•

Never reach into the rotating or blocked spreading disk whilst the motor

is running.

•

Comply with the regulations of the spreading material manufacturer.

•

It is essential to comply with the instructions of the spreading material

manufacturer in question.

•

Spreading tables and additional information about the spreading

material used can be requested from the spreading material

manufacturer in question.

•

LEHNER Agrar GmbH cannot accept any liability for the storage and

application of the spreading material.

Содержание POLARO E

















































Результаты поиска

Содержание POLARO E

Отзывы:

Похожие инструкции для POLARO E

Бренды по названию

Популярные бренды

LEHNER POLARO E, Инструкция по эксплуатации с перечнем запасных частей

Результаты поиска

Содержание POLARO E

Отзывы:

Похожие инструкции для POLARO E

Бренды по названию

Популярные бренды