LEGRAND Wattstopper FSP-212 Скачать руководство пользователя страница 2

2

INSTALLATION

Determine an appropriate mounting location inside the light fixture 

minimizing the electric light contribution to the sensor’s photocell. 

Allow a minimum distance of 0.2” (5.1mm) from the wiring end of the 

sensor to the wall of the fixture. 
There are two mounting methods for the FSP-212—using the threaded collar or using the snap-in tabs.

Threaded Collar Mounting

1.  Drill a hole 1.30” (33.0mm) in diameter through the sheet metal in 

the bottom of the fixture.

2.  Add the rubber gasket to the threaded collar, and install the sensor 

face down, parallel to the mounting surface. Ensure the rubber 

gasket touches the inside surface of the fixture. Install the plastic 

nut securely against the fixture to a torque of 25-30 in-lbs to 

ensure IP rating is maintained. 

3.  Align the locking features between the sensor and lens module 

and push the lens module forward until the o-ring seals firmly. Turn 

the lens module clockwise to ensure it locks in place.

4.  Connect wires as shown in wiring diagram.
5.  Restore power from the circuit breaker.

NOTE: 

An optional skirt can be installed in place of the tightening nut. 

See the 

Ordering Information

 table on page 4 for details.

Snap-In Mounting

1.  Cut a rectangular hole 32.6mm (± 0.2mm) by 89.9mm (± 0.2mm) 

through the sheet metal in the bottom of the fixture. The surface of 

the bottom of the fixture must be between .75mm and 3.2mm.

2.  Push the FSP-212 up from the below the fixture until the tabs 

“snap” and the fixture locks in place.

3.  Align the locking features between the sensor and lens module and 

push the lens module forward until the o-ring seals firmly. Turn the 

lens module clockwise to ensure it locks in place.

4.  Connect wires as shown in wiring diagram.
5.  Restore power from the circuit breaker.

NOTE: 

Snap-in mounting is not rated for IP66.

OUTDOORS—USE AT THE EXPOSED SENSOR COLLAR PART ONLY WHEN INSTALLED AT THE SPECIFIC 

LOCATION PER INSTALLATION INSTRUCTIONS WITH A LISTED OUTDOOR ENCLOSURE.

Threaded Collar Mounting

Fixture 

Wall

Lens Assembly

FSP-212

Outside 

Fixture Wall

Inside Fixture

Wall

89.9mm (± 0.2mm)

32.6mm (± 0.2mm)

Fixture Bottom

Cutout for snap-in mounting

Snap-in Mounting

WARNING

TURN THE POWER OFF AT THE CIRCUIT BREAKER 

BEFORE INSTALLING THE SENSOR.

Tightening

Nut

Tightening

Nut

Fixture 

Wall

Lens Assembly

FSP-212

Outside 

Fixture Wall

Inside Fixture

Wall

Rubber

Gasket

Rubber

Gasket

Dimming

Driver

LINE

NEUTRAL

NEUTRAL

GRAY (-)

VIOLET (+)

LOAD

Non-Dimming

Driver

LINE

NEUTRAL

NEUTRAL

LOAD

Note: Dim Level functionality does not 

apply when wired  as shown above.

Содержание Wattstopper FSP-212
















Отзывы: