background image

Wattstopper

 

®

Power Pack
Bloc d’alimentation
Fuente de alimentación

Installation Instructions • Instructions d’Installation • Instrucciones de Instalación

No: 24566 – 11/17  rev. 2

Catalog Numbers • Les Numéros de Catalogue • Números de Catálogo: BZ-50/BZ-50RC

Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China

BZ-50-U is BAA and TAA compliant (Product produced in the U.S.)

1.  Make sure power has been turned off at the circuit breaker. 
2.  Connect wires as shown in in the following diagrams, depending  

on the model and application.

At least three sensors can be powered by the power pack.

Installation Notes

1.  Power packs should be installed in accordance with state, local and national electrical codes and requirements.
2.  Power packs are designed to attach to existing or new electrical enclosures with 1/2 inch knockouts.
3.  For the BZ-50, most applications require UL listed, 18-22 AWG, 3-conductor, Class 2 cable for low voltage wiring. For plenum 

return ceilings, use UL listed plenum-approved cables.
For the BZ-50RC, connect an FS-C1 or FS-C3 cable between the RJ45 jack-equipped sensor and the BZ-50RC, as appropriate 

for the distance between the sensor and power pack. Other cable accessories are shown in the 

Ordering information

 section.

NOTE: 

The BZ-50RC can connect to a sensor with standard wiring terminals by using an FS-C2 cable.

4.  The BZ-50 BZ-50RC are Class 2 Output Power Supplies, suitable for parallel interconnection of up to 10 units maximum. These 

powerpacks are UL Listed for Interconnection of Power Sources in accordance with the National Electric Code.

5.  Refer to occupancy sensor data sheet to determine maximum number of sensors. Power pack mA output is 225mA.

SPECIFICATIONS

Voltages ...........................................120/277VAC,50/60Hz
 

 ..................... 230/240 VAC (Single Phase), 50/60Hz

Load Requirements
 

Ballast, Incandescent ............ 20amp @120/277VAC

 Eballast ........................................ 16amp @277VAC
 Motor ......................................... 1HP @120/240VAC
Output .................225mA @24VDC (with relay connected)
Low Voltage Input
 

Control ON  ...............................................12-24VDC

Operating Temperature .......................32°-104°F (0-40°C)

DESCRIPTION

The BZ-50 and BZ-50RC power packs are the foundation for any low voltage lighting control system. The BZ-50 and BZ-50RC  supply 

low voltage power to occupancy sensors and other control devices, switching line voltage in response to signals from control devices. 

The power pack is attached to existing junction boxes or mounted into fixture wiring trays.
High voltage connections should use at least 14-gauge. For the BZ-50, low voltage wiring should use at least 22-gauge wire. The 

BZ-50RC supplies low voltage power via shielded RJ45 cable. Always check local building codes. After initial wiring is complete, 

check wiring diagram to verify power pack is wired correctly. Improper wiring can cause damage to power pack, lighting system, and 

occupancy sensor.

INSTALLATION AND WIRING

WARNING:

 TURN THE POWER OFF AT THE 

CIRCUIT BREAKER BEFORE WIRING.

Low Voltage

Class 2

Line

Voltage

BZ-50

BZ-50RC

Low Voltage cable

with RJ45 connector

Line 

Voltage

BZ-50

BZ-50RC

Содержание Wattstopper BZ-50









Отзывы: