LEGRAND TyneTec Advent XT2 ascom VoWiFi i62 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 29

LEGRAND TyneTec Advent XT2 ascom VoWiFi i62 Скачать руководство пользователя страница 17

Doc No. FM0855 issue 2 Page 17

14. CHECK & UPGRADE DRAYTEK FIRMWARE

Connect the power to the Access Point and switch on, wait for the 5G & 2.4G

LED’s

to illuminate.

Connect LAN A1 to your Laptop Ethernet port using the UTP Patch lead supplied.
Open a web browser and type:

http://192.168.1.2

for a new or factory defaulted Access Point.

Enter the default

User Name

of “admin” and the default

Password

of “admin” and click

Login

.

Go to

System Maintenance

menu then select

Firmware Upgrade

as shown below;

The Current Firmware Version should be

1.3.3

or higher.

If an upgrade is required go to

https://www.draytek.co.uk/support/downloads

and select

VigorAP 903

.

Download the latest version of the

.all

file and then Upload and Upgrade via the web page shown above.

IMPORTANT:

you must

FACTORY RESET

the Access Point after a firmware upgrade. To do this; make sure

the device is powered-up with the ACT LED blinking and the 5G & 2.4G

LED’s

illuminated, hold down the

Factory Reset button for about 10 secs until the 5G & 2.4G

LED’s

go out, then wait for about 60 seconds for

the device to re-initialise.

«
...
15
16
17
18
19
...
»

Содержание TyneTec Advent XT2 ascom VoWiFi i62






























Отзывы:

Нет отзывов