LEGRAND NEAT NOVO Скачать руководство пользователя страница 37

Страница: 37 / 44

NOVO Technical Handbook - NE41 15013-02 v2.0

Range test

Range test can be used to confirm that a peripheral is registered and/or to test the

radio range.
NOVO returns to Service Menu after 5 minutes of inactivity.
NOVO indicates that the function has been chosen by flashing LEDs L1 – L3 in

synchronization.
When in Range test, activate a connected peripheral. If the unit is registered and in

range NOVO will play a short confirmation tone if the peripheral reports its battery

status as OK. NOVO will play a long confirmation tone if the peripheral reports its

battery status as low.

Mobile coverage test

Units that support GSM/4G as carrier will perform

Mobile coverage test

during range

test.
It will measure the mobile signal strength every 2 seconds and indicate the signal

strength with LEDs as shown in "Table 24".

Signal

Very weak (1)

Flash

Off

Flash

Weak (2)

Off

Flash

Average- (3)

Flash

Off

Flash

(4)

Off

Flash

Strong (5)

Flash

Very strong (6)

Flash

Mobile not installed*

Flash

Mobile not active

Off

Flash

Table 24.

LED indications when in Mobile coverage test.

* If Range test is initiated directly after startup,

Mobile not installed

will be indicated until the

mobile module is initiated and running.

Remove transmitter

There are three ways to remove a registered transmitter. All three methods described

in the following sections assume that function

Remove transmitter

has been chosen

by pressing

Alarm button (B1)

from the Service Menu.

NOVO will return to Service Menu after 20 seconds of inactivity.
NOVO indicates that the function has been chosen by flashing LEDs L1 – L3 in

synchronization.

Remove a transmitter by activation

Activate the peripheral and press

Alarm button (B1)

until timeout. If the peripheral

was registered, a short confirmation tone will be played, and the transmitter is

removed from the NOVO configuration. The unit will automatically return to Service

Menu.

Содержание NEAT NOVO













































Результаты поиска

Содержание NEAT NOVO

Отзывы:

Похожие инструкции для NEAT NOVO

Бренды по названию

Популярные бренды

LEGRAND NEAT NOVO, Техническое руководство

Результаты поиска

Содержание NEAT NOVO

Отзывы:

Похожие инструкции для NEAT NOVO

Бренды по названию

Популярные бренды