background image

19

KEOR T

Oper

ating M

anual

There are 7 different alarms defined. 
By default one alarm is assigned to each relay; however 

this can be changed by the user. It is also possible to 

assign the same alarm to each of the 4 relays.  

 

You may set each relay via this menu.
When you touch the 

save icon

 key, a confirmation  

pop-up bar will appear.
You should touch 

Yes

 to save the settings.    

Touch 

No

 to exit without saving the changes.

UPS records the event logs with the date and time 

information. Thus, the events can be followed 

chronologically. 
When you touch the 

save icon

 key, a confirmation  

pop-up bar will appear. You should touch 

Yes

 to save 

the settings. Touch 

No

 to exit without saving the 

changes.

UPS records the event logs with the date and time 

information. Thus, the events can be followed 

chronologically. 
When you touch the 

save icon

 key, a confirmation  

pop-up bar will appear. You should touch 

Yes

 to save 

the settings. Touch 

No

 to exit without saving the 

changes.

Set the date and time of UPS during pre-setting.

Содержание Keor T 10KVA


































































Отзывы: