LEGRAND Keor T 10KVA Скачать руководство пользователя | Manualshive

Страница: 21 / 65

background image

17

KEOR T

Oper

ating M

anual

Bypass voltage (Ph-N) and frequency information

of each phase are displayed. If the MAINS and AUX

Supply are connected in COMMON, Rectifier and

Bypass values will be the same.

Rectifier voltage (Ph-N), current and frequency

information of each phase are displayed. If the MAINS

and AUX Supply are connected in COMMON, Rectifier

and Bypass values will be the same.

When the Password Screen appears, enter 1111,

touch ENTER to confirm.

5.2.3.

Settings Menu

This menu is the section where all the settings related to UPS usage customization can be done.
User Password must be entered to make changes in this section.
User Password: 1111 (the password cannot be changed)

«
...
19
20
21
22
23
...
»

Содержание Keor T 10KVA


































































Отзывы:

Нет отзывов

Похожие инструкции для Keor T 10KVA

Бренд: Falcon Страницы: 15

Gamatronic B300

Бренд: SolarEdge Страницы: 101

Бренд: Powerware Страницы: 15

Бренд: PowerWalker Страницы: 19

Бренд: multimatic Страницы: 94

Бренд: Tycon Power Systems Страницы: 8

Бренд: Riello UPS Страницы: 85

MASTER HP-UL Series

Бренд: Riello UPS Страницы: 84

Бренд: PowerWalker Страницы: 11

9135 Two-in-One UPS 5000/6000 VA

Бренд: Eaton Страницы: 82

Бренд: SKD Страницы: 2

Бренд: SKD Страницы: 6

Бренд: Tripp Lite Страницы: 116

SmartPro SMART750RM1U

Бренд: Tripp Lite Страницы: 5

PowerControl C500R-060-B UPS

Бренд: CertaUPS Страницы: 70

Nirantar UPS-621V

Бренд: iBall Страницы: 2

Бренд: Sentinel Страницы: 46

Бренд: Ablerex Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды