manualshive.com logo in svg

LEGRAND Keor T 10KVA, Руководство по эксплуатации

Поделиться
Скачать
LEGRAND Keor T 10KVA Скачать руководство пользователя страница 16

12

5.1.1.

 Colour Graphical Touchscreen 

Energy Flow Diagram/Modes Of Operation

 and 

Menus

 are displayed on LCD.

The description of the symbols in the energy flow diagram:

Bypass Input:

  If Bypass voltage is OK and synchronizes with inverter; it lits Green, If Bypass voltage is 

OK and not synchronizes with inverter; it lits Orange.

Rectifier Input:

 If Input voltage is OK, it lits Green.

Rectifier: 

Converts AC voltage at the input into DC voltage. You may reach the rectifier measurements 

by touching it. 

Bypass Line:

 Shows that the loads are supplied via Bypass and line colour is Orange. If UPS is on Eco 

Mode it is Green. 

Battery: 

Shows battery conditions. If it is discharging the indicator goes down, if it is charging the 

indicator goes up. You may reach the battery/DC measurements by touching it.  

Inverter:

 Converts DC voltage into AC voltage. You may reach the output measurements by touching 

it.   

Operation Mode Information: 

 Shows UPS’s current operation mode. 

Load:

 Shows the percentage of the load as numerical and graphical information. If there is overload at 

the output the load graphic lits Red. You may reach the output power measurements by touching it.

Menu:

 You may reach the menus by touching it.

Configuration: 

It indicates if UPS is in parallel or single operation configuration. In Single Mode; there 

is no symbol.

Time: 

It indicates the time.

Circuit Breaker: 

It appears if battery Fuse is in “OFF” position or battery fuse has blown. If battery Fuse 

is in “ON” position; the circuit breaker icon is not displayed, instead battery capacity percentage is 

displayed. 

Alarms:

 If there is an alarm on UPS this icon appears and informs the user by flashing. You may reach 

the alarms by touching it.

Exclamation Mark:

 Indicates that there is a problem where the icon appears.

Transfer: 

Indicates that transfer to bypass is disabled.  

Wrench: 

Indicates that UPS requires Periodic Preventive Maintenance. 

Temperature:

 Indicates ambient temperature of UPS is too high. 

Generator Mode:

 Indicates UPS operates on Generator Mode.

10

1

2

3

14

5

6

12

14

13

18

4

16

15

8

11

17

7

9

1

2

3

4

5

6

7

8

9

10

11

12

13

14
15

16

17
18

Содержание Keor T 10KVA


































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды