LEGRAND DA-LITE Tensioned Advantage Series Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 61

background image

6

If your screen was shipped with the motor and roller already installed proceed to step 6.

1. Remove the screw from each end of the access door

(front door) and open the door. See figure 1.

2. Carefully unpack screen and roller assembly. Leave

packing paper on the roller.

3. Place the roller assembly into the case with the

motor on the left side. The limit switches should be
facing down. Line up the square pin on the motor
with the square hole in the bracket. Secure with
cotter pin. See figure 2.

4. Lift the pin end (right end) of the roller into position

and slide the bracket onto the roller pin. Tighten two
nuts to secure the bracket. Secure pin end with
cotter pin. See figure 3.

5. Complete electrical hook-up by snapping motor wire

connector into case connector.

6. Remove shipping brackets by removing the hex head

screws from aluminum slat and case. Slat should
move freely. See figure 2. (Only if the roller assembly
is preinstalled.)

7. Test installation by operating the screen several

times. Be prepared to stop the screen. Standard Duty
Cycle: 1 MIN. ON/3 MIN. OFF. The fabric door (rear
door) will not close until the wall switch is placed in
the up position and when the screen motor stops at
its limit switch in the up direction.

CAUTION: Excessive continuous operation may

cause the motor to overheat. If this happens the
motor will shut off until it cools to a normal
operating temperature.

ATTENTION! Le fonctionnement continu et

excessif peut provoquer une surchauffe.Si cela se
produit, les moteurs s'arrêteront jusqu'à qu'ils se
soient refroidis à la température normale de
fonctionnement.

8. Remove any shipping foam attached to the inside of

the access and fabric doors before operation.

9. Run the screen down enough to open the fabric door.

Close the access door and reinstall the screws to
secure the door.

Figure 2

Figure 3

Screen Motor

Adjustment

Knob “Down”

Door

Microswitch

Door Motor

Hex Head Screws

Shipping

Bracket

Adjustment

Knob “Up”

Fabric

Door

Access Door

Cotter Pin

Cotter Pin

Pin End

SCREEN AND ROLLER ASSEMBLY INSTALLATION

«
...
4
5
6
7
8
...
»

Содержание DA-LITE Tensioned Advantage Series






























































Отзывы:

Нет отзывов

Похожие инструкции для DA-LITE Tensioned Advantage Series

Бренд: NEC Страницы: 83

Бренд: NEC Страницы: 2

Бренд: NEC Страницы: 6

Бренд: NEC Страницы: 4

Showcase Series HT1100

Бренд: NEC Страницы: 6

Бренд: NEC Страницы: 99

Бренд: NEC Страницы: 114

Бренд: NEC Страницы: 82

Showcase Series HT1100

Бренд: NEC Страницы: 8

Бренд: NEC Страницы: 6

Бренд: Samsung Страницы: 67

Бренд: Samsung Страницы: 63

Бренд: Navitar Страницы: 42

Бренд: Niko Страницы: 72

Ultimate Access XL V

Бренд: Draper Страницы: 7

Бренд: Digital Projection Страницы: 58

Reflection VX-3C

Бренд: Runco Страницы: 129

PJL1035 - LCD Projector SXGA

Бренд: ViewSonic Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды