LEGRAND DA-LITE Tensioned Advantage Series Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 61

background image

30

1. Hang case and attach to support structure with

bolts. See Suggested Methods of Installation.

2. Tighten bolts until trim flange is flush with ceiling.

NOTE: For proper operation, case must be
levelled side to side and front to back.

3. Remove 2 screws to open junction box. Install

electrical connections that apply to your unit.
Make sure to review the wiring diagram for proper
hook up. Replace junction box cover and secure
with 2 screws.

NOTE: Must be installed in accordance with the
requirements
of the Local Building Codes, the Canadian
Electrical Code (CEC), CAN/CSA C22.1 and the
National Electric Code (NEC), NFPA 70.

1. Carefully unpack case from shipping carton.

2. Set aside the Installation Kit. Items inside will be

used
during installation.

3. Make sure to recheck measurement of case for

proper installation clearance.

4. Remove any protective foam covering the outside

of the case.

1/2" and 5/16" Open Wrench

or Socket Driver

1/8" Hex Key

(included)

5. For shipping purposes, foam is also inserted

between the roller brackets and end caps (Figure
1). Remove these foam blocks from the ends.

6. Remove the hanger brackets from the top of the

case using a 1/2" wrench. Do not discard the
hardware; it will be used during case installation
to re-attach the hanger brackets for mounting.

If your case was ordered in advance of the
screen and
roller assembly, your installation is now
complete. Continue to step 4 if your Tensioned
Advantage was ordered as a complete unit.

4. Use a 5/16" socket or wrench and the supplied

1/8" hex key to remove silver shipping brackets
attached to slat and screen case.

5. Test installation by running screen up and down a

few times.
Be prepared to stop screen should any objects
obstruct the movement of the screen. To prevent
damage to the motor,
the standard duty cycle is 1 minute on and 3
minutes off.

TOOLS REQUIRED FOR INSTALLATION

PRE-INSTALLATION

CASE INSTALLATION

«
...
28
29
30
31
32
...
»

Содержание DA-LITE Tensioned Advantage Series






























































Отзывы:

Нет отзывов

Похожие инструкции для DA-LITE Tensioned Advantage Series

Бренд: Optoma Страницы: 1

ZEB-PixaPlay 26

Бренд: Zebronics Страницы: 13

Бренд: Barco Страницы: 17

Бренд: Eiki Страницы: 2

Бренд: Cineversum Страницы: 64

Бренд: Yaber Страницы: 116

CineVERSUM 110 R9010120

Бренд: Barco Страницы: 135

Бренд: Barco Страницы: 3

Бренд: Panasonic Страницы: 131

Бренд: InFocus Страницы: 4

DLA-G15U - D-ila Projector, 1500 Ansi Lumens

Бренд: JVC Страницы: 8

Бренд: JVC Страницы: 7

Бренд: JVC Страницы: 6

DLA-HD10KSU - 1080p Home Theater Projector

Бренд: JVC Страницы: 6

Бренд: JVC Страницы: 8

DLA-G150CL - D-ILA Projector - 100 ANSI Lumens

Бренд: JVC Страницы: 4

Бренд: JVC Страницы: 4

Бренд: JVC Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды