LEGRAND DA-LITE Tensioned Advantage Series Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 61

background image

28

DISCLAIMER

IMPORTANT SAFETY INSTRUCTIONS

ORIGINAL INSTRUCTIONS

When using your video equipment, basic safety precautions should always be followed, including the following:

1. Read and understand all instructions before using.

2. Maximum surrounding air temperature 122°F (50°C).

3. Main disconnect must be incorporated in the fixed

wiring in accordance with the wiring rules.

4. Rated for indoor use only.

5. Use copper rated conductors rated 167°F (75°C) or

higher.

6. If the supply cord is damaged, it must be replaced by

the manufacturer, its service agent or similarly
qualified persons in order to avoid hazard.

7. Supplied drive is only intended for use in Da-Lite

screen models Advantage, Contour, and
Cosmopolitan.

8. Position the cord so that it will not be tripped over,

pulled, or contact hot surfaces.

9. If an extension cord is necessary, a cord with a

current rating at least equal to that of the appliance
should be used. Cords rated for less amperage than

the appliance may overheat.

10. To reduce the risk of electric shock, do not

disassemble this appliance. Contact an authorized
service dealer when repair work is required.
Incorrect reassembly can cause electric shock when
the appliance is used subsequently.

11. The use of an accessory attachment not

recommended by the manufacturer may cause a risk
of fire, electric shock, or injury to persons.

12. Failure to provide adequate structural strength for

this component can result in serious personal injury
or damage to equipment! It is the installer’s
responsibility to make sure the structure to which
this component is attached can support the weight
of all equipment. Reinforce the structure as required
before installing the component.

13. Use this projection screen only for its intended use

as described in these instructions. Do not use
attachments not recommended by the manufacturer.

Save These Instructions

Legrand AV Inc. and its affiliated companies and subsidiaries (collectively, “Legrand AV”), intend to make this
manual accurate and complete. However, Legrand AV makes no claim that the information contained herein
covers all details, conditions or variations, nor does it provide for every possible contingency in connection with
the installation or use of the products described herein. The content herein is subject to change without notice
or obligation of any kind. To the maximum extent permitted by applicable law, Legrand AV makes no
representation or warranty, expressed or implied, regarding the information contained herein. Furthermore,
Legrand AV assumes no responsibility for accuracy, completeness or sufficiency of the information contained in
this document.

Da-Lite® is a registered trademark of Legrand AV. All rights reserved.

«
...
26
27
28
29
30
...
»

Содержание DA-LITE Tensioned Advantage Series






























































Отзывы:

Нет отзывов

Похожие инструкции для DA-LITE Tensioned Advantage Series

Бренд: NEC Страницы: 2

PTL785U - LCD PROJECTOR UNIT

Бренд: Panasonic Страницы: 20

PTL597UL - LCD VIDEO PROJRCTOR

Бренд: Panasonic Страницы: 64

Бренд: Panasonic Страницы: 13

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 81

Бренд: Panasonic Страницы: 184

Бренд: Panasonic Страницы: 270

PTLB75NTU - LCD PROJECTOR

Бренд: Panasonic Страницы: 62

PTLB80NTU - LCD PROJECTOR

Бренд: Panasonic Страницы: 118

PTLB51NTU - LCD PROJECTOR - MULTI LANGUAGE

Бренд: Panasonic Страницы: 10

PTLB30NTU - LCD PROJECTOR - MULTI-LANG

Бренд: Panasonic Страницы: 144

PTD7700U - DLP PROJECTOR

Бренд: Panasonic Страницы: 132

PTD5500U - DLP PROJECTOR

Бренд: Panasonic Страницы: 94

PTAX200U - LCD PROJECTOR

Бренд: Panasonic Страницы: 54

PTFW100NTU - LCD PROJEC. WIRELESS

Бренд: Panasonic Страницы: 2

Бренд: Niko Страницы: 72

Бренд: Mitsubishi Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды