background image

16/29

17/29

Technical data sheet: S000074637EN-5

Updated: 12/03/2015

Created: 15/04/2014

mber(s): 0 484 22

Catalogue number(s): 0 484 22

KNX multiapplication controller 16 outputs

8. COmmUNiCaTiON OBJECTS (CONTiNUED)

Shutter 2-input

No.

Object name

function

Size

flags

2

(16, 30,

44, 58, 72,

86, 100)

Input G(,H)1 (3

 7)+

G(,H)2 (4

 8)

Shutter Up/

Down

1.008 DPT_

UpDown

CWT

The movement commands Up/Down are sent via the address linked

with this object in order to raise/lower the solar protection.

8

(22, 36,

50, 64, 78,

92, 106)

Input G(,H)1 (3

 7)+

G(,H)2 (4

 8)

Shutter Stop

- slats

1.009 DPT_

OpenClose

CWT

The commands“STOP” or“Slats OPEN/CLOSE” are sent via the group

address linked with this object.

4

(18, 32, 46,

60, 74, 88,

102)

Input G(,H)1 (3

 7)+

G(,H)2 (4

 8)

Enable

1.003 DPT_

Enable

CW

Enable telegrams are received via the group address linked with this

object. They are used to lock (disable) or unlock (enable) the correspon-

ding input.

They are only visible if“Add status object”parameter value is set to yes.

Switch

This function is used for 2 inputs with a switch to send a up,stop or down

telegram : the contact is closed or opened, a telegram is sent.

Parameters

Setting

Xn - Switching value when contact is

closed

No reaction

Up

Down

Here an adjustment is made to define which movement command is

written into the storage cell of the communication object and sent

after a rising edge. The rising edge corresponds to a change in the

signal status at the input from logical “0” to “1”.

“No reaction”: action does not change the object value and also does

not send a telegram.

“Up”: when the contact is active, the command UP is transferred into

the communication object and sent.

“Down

”: when the contact is active, the command DOWN is transferred

into the communication object and sent.

Xn - Switching value when contact is

opened

No reaction

Stop

Here an adjustment is made to define which switching movement

command is written into the storage cell of the communication object

and sent after a falling edge in the signal status at the channel (input).

The falling edge corresponds to a change in the signal status at the

input from logical “1” to “0”.

“No reaction”: action does not change the object value and also does

not send a telegram.

“Stop”: when the contact is inactive, the command stop is transferred

into the communication object and sent.

tion

ng value is written

and sent after short

bject value and also

nary value, “1”) is

t.

nary value ”0”) is

t.

ed in the communi-

tion

ng value is written

and sent after long

the object value and also

y value, “1”) is trans

-

Dim –

tion

ing value is written

and sent after long

the object value and also

ease 100%” is trans-

ease 100%” is trans-

tion

ing value is written

and sent when relea-

the object value and also

er a long push, the dim-

ation object and

ond

ond

onds

ds

ds

ds

ds

detecting a long

ommunication object (sta-

or other purposes.

ormally open contact

y closed contact

o the channel is adjusted here.

t of the input is active when

t of the input is active when

blocked via an additional

f an input is blocked (Enable value = 0) the status

Parameters

Setting

Xn+1 - Switching value when contact

is closed

No reaction

Up

Down

Here an adjustment is made to define which movement command is

written into the storage cell of the communication object and sent

after a rising edge. The rising edge corresponds to a change in the

signal status at the input from logical “0” to “1”.

“No reaction”: action does not change the object value and also does

not send a telegram.

“Up”: when the contact is active, the command UP is transferred into

the communication object and sent.

“Down

”: when the contact is active, the command DOWN is transferred

into the communication object and sent.

Xn+1 - Switching value when contact

is opened

No reaction

Stop

Here an adjustment is made to define which switching movement

command is written into the storage cell of the communication object

and sent after a falling edge in the signal status at the channel (input).

The falling edge corresponds to a change in the signal status at the

input from logical “1” to “0”.

“No reaction”: action does not change the object value and also does

not send a telegram.

“Stop”: when the contact is inactive, the command stop is transferred

into the communication object and sent

Contact type

Normally open contact

Normally closed contact

The contact type of the input attached to the channel is adjusted here.

“Normally open contact”: the contact of the input is active when

closed, inactive when opened.

“Normally closed contact”: the contact of the input is active when

opened, inactive when closed.

add enable object

Yes /

No

The parameter determines if the input can be blocked via an additional

Enable object or not. If an input is blocked (Enable value = 0) the status

changes at this input are not transmitted.

Push

This function is used for 2 inputs with push button to send a up,stop or down

telegram : the push is short or long, a telegram is sent.

S000074637EN-5.indd 17

20/05/15 10:16

Содержание 0 484 22






























Отзывы: