background image

3

ADVISORY

FOR OPTIMUM ADJUSTABLE BASE 

OPERATION, USE A GROUNDED, ELECTRICAL 

SURGE PROTECTION DEVICE (NOT 

INCLUDED). FAILURE TO USE A SURGE 

PROTECTION DEVICE COULD COMPROMISE 

SAFETY OR CAUSE PRODUCT MALFUNCTION.

WARNING

!

READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT

IMPORTANT INFORMATION

ELECTRICAL RATING 

Input: 100-240VAC, 50/60Hz, 1.6A. Output: 29VDC, 1.8A.

ELECTRICAL GROUNDING

This product is equipped with a polarized or grounded 
electrical power cord. The power cord will only fit into a 
grounded, electrical surge protection device (not included) 
or a grounded electrical outlet. 

WARRANTY WARNING

Do not open any control boxes, motors or remote control 
devices (with the exception of the remote control and 
power down box battery compartments). The product 
warranty will be void if these components are tampered 
with. Do not attempt to alter component wiring or adjust 
or modify the structure of the product in any way or the 
warranty will be void. Any repair or replacement of base 
parts must be performed by authorized personnel. 

 

LUBRICATION

This product is designed to be maintenance free. The 
lift motors are permanently lubricated and sealed—no 
additional lubrication is required. Do not apply lubricant 
to lift motor lead screws or any nylon nuts or the base may 
inadvertently creep downward from the elevated position.

PRODUCT RATINGS

The base lift motors are 

not

 designed for continuous use. 

Reliable operation and full life expectancy will be realized 
as long as the lift motor operation does not exceed 
two (2) minutes over a twenty (20) minute period, or 
approximately 10% duty cycle. 

Note: Massage equipped 

bases are not designed for continuous, extended massage 

operation. Massage systems are rated for a maximum of 

2 hours of use within any 6 hour period.

 Any attempt to 

circumvent or exceed product ratings will shorten the life 
expectancy of the product and may void the warranty.
The recommended maximum weight (including mattress) 
is 700 lb (318 kg) distributed evenly across the base. 
This product is not designed to support or lift this amount 
in the head or foot sections alone. 

Note: Exceeding the 

recommended weight restrictions could damage the base 

and void the warranty.

For best performance, consumers should enter and exit 
the adjustable base with the base in the flat (horizontal) 
position. Avoid placing entire weight on head or foot 
section of the base, including when in the raised position.

 

DO NOT STAND ON BASE AT ANY TIME.

UL (Underwriters Laboratories) recognized components.

CFR 1633 approved for use with most mattresses.

LOCATION ENVIRONMENT

The level of sound experienced during operation is directly 
related to the location environment. For example, when 
a base is located on a hardwood floor with the massage 
feature in operation, a vibrating tone will be audible. 
To minimize this resonance, place a piece of carpet, or 
rubber caster cups, under each leg or caster of the base.

 

Содержание Plymouth K-132

















Отзывы: