background image

[4] 

 

Start-Up

 

Set-up Prior to Installing at Retail 
Location: 

The Vending Machine refrigeration system will 
arrive at the customer location ready to operate 
within design parameters that have been tested and 
deemed optimum for ice storage.   

 

Prior to installing the Vending Machine at the retail 
location, perform a series of steps for set up and 
checks to ensure the unit was not damaged during 
delivery.  NOTE: The pallet and all packaging 
material must be removed before proceeding. 

 

 

1.

 

Prior to energizing the Vending Machine, place 
the MODE key in the ‘RUN’ position and the 
DOORS key in the ‘LOCK’ position. 

 

Failure to place the MODE key in the 
‘RUN’ position prior to energizing will 
result in a blank screen on the card 
reader. 

 
2.

 

Energize the Vending Machine and let it run for 
about 1 hour. 

 

Within a few seconds of being plugged 
in, the compressor and condenser fan 
motor will energize.   

o

 

NOTE: If the unit does not start 
within a few seconds, check the 
on/off switch located next to the 
electronic control display.   

 

The Vending Machine will continue to 
run until it has reached the factory pre-
set cut-out temperature of +16 degrees F.  

Reporting Provision Code: 

3.

 

At start-up, watch for and record the provision 
code to be displayed on the card reader.  Report 
the provision code to Vendnovation by calling 
425-637-2344. 

 

Vendnovation will provision the Vending 
Machine and update firmware if needed. 

 

Vendnovation will assign product and link 
to test credit card system. 

Door Locks and Sensors 

After the unit has been running for 1 hour, the doors 
can now be tested. 

 

4.

 

Check the doors – they should be locked. 

 
5.

 

Turn the MODE key to the ‘SET-UP’ position. 

 

“Synchronize Inventory” will display 

 
6.

 

Press cancel button once 

 

“Hardware” will display 

 

7.

 

Press enter button once 

 

“Test Door“ will display 

 

8.

 

Press enter button once 

 

The doors will unlock and “Door Closed” 

 

If it showing “Door Open” the door sensors 
need to be adjusted. 

 

9.

 

Open and close each door  

 

As each door is opened and closed the 
display should show “Door Open” or “Door 
Closed” 

 

10.

 

Press cancel button once 

 

The doors will lock again 

 

11.

 

Return the MODE key to the ‘RUN’ position. 

Calibrate Scale:  

12.

 

Turn the MODE key to the ‘SET-UP’ position. 

 

“Synchronize Inventory” will display 

 
13.

 

Press cancel button once 

 

“Hardware” will display 

 

14.

 

Press cancel button three times 

 

“Calibrate Scale“ will display 

 
15.

 

Press enter button once 

Содержание VM40















Отзывы: