Lectrotab ELECTROMECHANICAL TRIM TAB SYSTEMS Скачать руководство пользователя страница 10

Operation

1)

Begin with the tabs fully retracted by pressing the two “BOW UP” or bottom switch buttons until the 

LEDs are flashing on the Oval or Wireless control or after 8 seconds for the flat rocker switch control. 

2) Bring the boat to a comfortable cruising speed.

Trimming the Port Side:

1)

Press the upper left “PORT BOW DOWN” switch until you feel the boat’s port side begin to go down 
then release the upper left “PORT BOW DOWN” switch. The Oval and Wireless control will light LEDs 

on the right side of the control to indicate that the starboard tab is being deployed to lift the 
starboard transom up and causing the port bow or side to go down.  If it is preferred to switch the 
LED indicator to the opposite side indicating the bow is going down, then please review the Oval or 
Wireless program chart at 

www.lectrotab.com

under Products/Controls.

2)

Press the bottom left “PORT BOW UP” switch until you feel the boat’s port side begin to come up 
then release the lower left “PORT BOW UP” switch.

Trimming the Starboard Side:

1)

Press the upper right “STBD BOW DOWN” switch until you feel the boat’s starboard side begin to go 

down then release the upper right “STBD BOW DOWN” switch. The Oval and Wireless control will 

light LEDs on the left side of the control to indicate that the port tab is being deployed to lift the port 
transom up and causing the starboard bow or side to go down. 

2)

Press the bottom right “STBD BOW UP” switch until you feel the boat’s starboard side begin to come 
up then release the bottom right “STBD BOW UP” switch.

Adjusting Bow Down or Up:

1)

Press the lower right “STBD BOW UP” and lower left “PORT BOW UP” buttons at the same time for 

8 seconds or until the top two LED are flashing indicating the tabs are fully retracted. Press the upper 

right “STBD BOW DOWN” and upper left “PORT BOW DOWN” buttons at the same time , and the 

bow should begin to go down. Keep these buttons pressed until the boat achieves the proper level 
and then release the buttons. Press both BOW UP buttons to bring the bow back up if necessary.

10

Содержание ELECTROMECHANICAL TRIM TAB SYSTEMS













Отзывы: