LeCroy ZD200 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 31

LeCroy ZD200 Скачать руководство пользователя страница 6

ZD200 Differential Probe

ZD200-GSM-REVA

6

Introduction

The ZD200 Differential Probe is ideally suited for automotive
and serial data signals. The wide dynamic range (+/- 20V
differential) and 1 MOhm input resistance make the ZD200
ideally suited for a wide range of applications.

The ZD200 probe can be used with LeCroy’s WaveSurfer,
WaveRunner, WavePro, and WaveMaster series platforms with
firmware version 6.4.1.x or later.

With the ProBus interface, the ZD200 probe becomes an
integral part of the oscilloscope. The probe can be controlled
from the oscilloscope’s front panel. The oscilloscope provides
power to the probe, so there is no need for a separate power
supply or batteries.

Key Benefits

The ZD200 probe features:



1 MOhm input resistance



Low input capacitance



Wide dynamic range



ProBus interface



Complete accessory kit consisting of 3 sets of
grabbers, one alligator clip, 2 sets of leads and
2 tip options for probing a variety of test points

«
...
4
5
6
7
8
...
»

Содержание ZD200
































Отзывы:

Нет отзывов