LeCroy ZD200 Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 31

LeCroy ZD200 Скачать руководство пользователя страница 12

ZD200 Differential Probe

ZD200-GSM-REVA

12

Care and Maintenance

Cleaning

The exterior of the probe and cable should be cleaned, using a
soft cloth moistened with water. The use of abrasive agents,
strong detergents, or other solvents may damage the probe.
Always ensure that the input leads are free of debris.

The probe case is not sealed and should never be immersed in
any fluid.

Calibration Interval

The recommended calibration interval is one year.
(Performance Verification and Adjustment Procedures are
included in this manual.)

Service Strategy

The ZD200 probe utilizes fine pitch surface mount devices. It is
therefore impractical to attempt to repair in the field.
Defective probes must be returned to a LeCroy service facility
for diagnosis and exchange. Defective probes under warranty
are repaired or replaced. A probe that is not under warranty
can be exchanged for a factory refurbished probe for a modest
fee. You must return the defective probe in order to receive
credit for the probe core.

«
...
10
11
12
13
14
...
»

Содержание ZD200
































Отзывы:

Нет отзывов