manualshive.com logo in svg

LeCroy ZD200, Инструкция по эксплуатации, Страница: 26 / 31

Поделиться
Скачать
LeCroy ZD200 Скачать руководство пользователя страница 26

ZD200 Differential Probe 

  ZD200-GSM-REVA 

26 

Safety Requirements 

 

CAUTION

 

Avoid personal injury or damage to your accessory or any 
equipment connected to it by reviewing and complying with 
the following safety precautions: 

 

Use only as intended

. The accessory is intended to be 

used only with the compatible LeCroy instruments. Use 
of the accessory and/or the equipment it is connected to 
in a manner other than specified may impair the 
protection mechanisms. 

 

Connect and disconnect properly

. Avoid damage 

through excessive bending of cables and other 
equipment. 

 

Do not use in wet/damp or explosive atmospheres

. 

 

For indoor use only

. The accessory is intended for indoor 

use and should be operated in a clean, dry, environment. 

 

Do not operate with suspected failures

. Do not use the 

product if any part is damaged. All maintenance should 
be referred to qualified service personnel. 

 

Keep product surfaces clean and dry

. 

 

Completely assemble the measurement instrument 
before circuit/signal contact

. Connect probe to the 

measurement instrument before connecting the probe 
test leads to a circuit/signal being tested. 

 

Do not apply a voltage to any input that exceeds the 
maximum rating of that input

. Refer to the 

Specifications on LeCroy website at 

www.lecroy.com

 for 

detailed information. 

 

Be careful with sharp tips

. Handle the probe with care 

as it has sharp tips that may cause bodily injury if not 
handled properly. 

Содержание ZD200
































Отзывы:

Нет отзывов