LeCroy ZD200 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 31

LeCroy ZD200 Скачать руководство пользователя страница 27

Instruction Manual

ZD200-GSM-REVA

27

Compliance Information

This LeCroy accessory is CE Compliant and bears the CE mark.

CE Declaration of Conformity

This ZD200 Probe meets intent of the European Council
Directive 2006/95/EEC for Product Safety and 2004/108/EEC
for Electromagnetic Compatibility. Compliance was
demonstrated to the following specifications as listed in the
Official Journal of the European Communities:



EN 61010-031:2002 Safety requirements for electrical
equipment for measurement, control, and laboratory
use.

Part 031: Safety requirements for the hand-held probe
assemblies for electrical measurement and test.

The design of the differential probe has been verified to
conform to EN 61010-031 safety standard per the
following limits:

o

Installation (Overvoltage) Category I: Refers to
signal level which is applicable for equipment
measuring terminals that are connected to source
circuits in which measures are taken to limit
transient voltages to an appropriate low level.

o

Pollution Degree 2: Refers to an operating
environment where normally only dry non-
conductive pollution occurs. Occasionally a
temporary conductivity caused by condensation
must be expected.



EN 61326-1:2006, EN 61326-2-1:2006 EMC
requirements for electrical equipment for measurement,
control and laboratory use.

o

EN 55011/A2:2002 Radiated and Conducted
Emissions, Group 1, Class A *

«
...
25
26
27
28
29
...
»

Содержание ZD200
































Отзывы:

Нет отзывов