LDG YT-450 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 22

LDG YT-450 Скачать руководство пользователя страница 10

PAGE 10

Rotate the

DSP/SEL

knob one click clockwise until “CATRATE” is showing. Push in on the

DSP/SEL

knob. Rotate the

DSP/SEL

knob until “38400” is showing. Push in on the

DSP/SEL

knob one final time. Now push and hold the “

F

” button to return to normal operation.

FT-950 Installation

Connect the

ANT 1

jack on the FT-950 to the

TX

jack on the back of the YT-450, using a 50

ohm coax cable rated 125 watts or greater.

Connect the 8-pin mini-DIN connector on the supplied radio interface cable to the jack

marked “TUNER” on the FT-950. Connect the adjacent DB-9 plug to the “CAT” jack on the FT-
950.

On the other end of the interface cable, connect the DC coax plug to the jack marked

“Power” on the rear of the YT-450 tuner. Connect the remaining DB-9 plug to the jack marked
“Radio” on the YT-450.

On the FT-950, press the

MENU

button on the front panel to bring up the menu system. Push

in on the

SELECT

knob once or twice so that the non-numbered menu items are showing.

«
...
8
9
10
11
12
...
»

Содержание YT-450























Отзывы:

Нет отзывов