manualshive.com logo in svg

Lawson TXLS ROV, Руководство по эксплуатации и техническому обслуживанию

Поделиться
Скачать
Lawson TXLS ROV Скачать руководство пользователя страница 24

LAWSON ENGINEERS LTD                                                         Ref : PJ1682 
                                                                                                          Issue Date : 06.06.2006 

Locked / Damped 

Selector switch. Normal position is in Damped. Only 
select Locked if hoisting with the winch with the ‘A’ 
frame inboard. When the ‘A’ frame is outboard or in 
motion, select Damped. 

Snubber In/Out Motion. 

Toggle switches to drive snubber in or out using the 
damping cylinders. These controls operate whether 
the snubber is locked or in damped mode. 

 
Rotate Motion 

Toggle switches to control clockwise or counter 
clockwise motion. 
Note – When rotating the snubber with the TMS       
latched ensure the umbilical is slack to reduce the risk 
of birdcaging the armour. 

Snubber Up / Left 

Selector switch to move snubber either up and down 
or left and right. 

Snubber Up/Down                          Toggle switches to control the 600mm up/down 

feature.

 

There is a pressure relief on the Down motion, 
however it is not good practice to over lower the 
snubber as this will crush the TMS against the ROV. 
 

Snubber Left/Right 

Toggle switches to control the 20 degrees sideways 
motion. This feature is designed to allow the snubber 
to be aligned with the umbilical in strong current 
areas. Do not use this function if the vehicle is latched 
in or in air. Fully raise the snubber to ensure it is in 
the centre position before luffing the A-Frame. 

CAUTION –

 The 20 degrees sideways motion is only 

limited by proximity switches. If these fail the 
structure will be damaged as the cylinders over 
extend. Check the function of the proximity switches 
regularly and keep a good visual check if operating 
close to the limit of the swing. 

 
SNUBBER DAMPING 
 
The damping rate is controlled by flow control valve (95), located adjacent to the 5 stack 
valve under the skid deck.  By rotating the adjuster clockwise the damping rate is 
increased and by rotating the adjuster anti-clockwise the rate is reduced.  

 

SNUBBER LATCHING 
 
To latch the vehicle in, hoist the R.O.V. into the snubber, the termination cone will push 
past the latches and they will snap back into position under the cone.  If you now attempt 
to lower the R.O.V. the umbilical will go slack.  If required the latches can be powered 
back into position by pushing the latch release Toggle switch. 

- 24 - 

 

Содержание TXLS ROV




























































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды