manualshive.com logo in svg

LAVAMAC LDR-900-S, Установка, эксплуатация и обслуживание

Поделиться
Скачать
LAVAMAC LDR-900-S Скачать руководство пользователя страница 3

Front Matter

  Part No. 70476501ENR7

  3

Front Matter

Installation must conform with local codes or, in the absence of local codes, with:

In the U.S.A., installation must conform to the latest edition of the American National Standard Z223.1/ NFPA 54 “National Fuel Gas
Code” and Standard ANSI/NFPA 70 “National Electric Code.”

In Canada, installation must comply with Standards CAN/CSA-B149.1 or Natural Gas and Propane Installation Code and CSA C22.1,
latest edition, Canadian Electric Code, Part I.

In Australia and New Zealand, installation must comply with the Gas Installations Standard AS/NZS 5601 Part 1: General
Installations.

WARNING

FOR YOUR SAFETY, the information in this manual must be followed to minimize the risk of fire or explosion
or to prevent property damage, personal injury or death.

W033

WARNING

•

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other
appliance.

•

WHAT TO DO IF YOU SMELL GAS:

•

Do not try to light any appliance.

•

Do not touch any electrical switch; do not use any phone in your building.

•

Clear the room, building or area of all occupants.

•

Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

•

If you cannot reach your gas supplier, call the fire department.

•

Installation and service must be performed by a qualified installer, service agency or the gas supplier.

W052

IMPORTANT: Information must be obtained from a local gas supplier on instructions to be followed if the user
smells gas. These instructions must be posted in a prominent location. Step-by-step instructions of the above
safety information must be posted in a prominent location near the tumble dryer for customer use.

IMPORTANT: The installer must fully test the tumble dryer after installation and demonstrate to the owner how to
operate the machine.

WARNING

To reduce the risk of electric shock, fire, explosion, serious injury or death:

•

Disconnect electric power to the tumble dryer before servicing.

•

Close gas shut-off valve to gas tumble dryer before servicing.

•

Close steam valve to steam tumble dryer before servicing.

•

Never start the tumble dryer with any guards/panels removed.

•

Whenever ground wires are removed during servicing, these ground wires must be reconnected to ensure
that the tumble dryer is properly grounded.

W002R1

Содержание LDR-900-S






















































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды