background image

 

 

 

 
 
 

Step 1. With assistance, place the vertical  column  in  its tilt back seat on the Body Assembly. Push the air hose  
through the large round hole into the body.

 

 
 
 

 

Step 2. Insert the pin (140) through the  column and fasten it  with 
screws (143) and washers (142).

 

 
 
 
 
 
 
                                                               

 

Step 3. Using the screw (137) tighten with the self-locking nut (139) and washer (138) to connect the pin 
of the post tilting cylinder. 
 
 
 
 
 
 

Step 4. Remove the four screws from the left side cover and remove it. Connect the air hose from the col-
umn to the 6mm connector. 
 
Step 5. Replace the side cover and fasten with its screws. 
 
Step 6. Install the plastic guard (134) and fix it with the screws and washer (135,136). 
 
 

 
Step 7. Install the stopper bolt (23) with self  lock nut 
(24). Don’t  too tight.  
 
 
 
 
 
 

5-2 Pneumatic link up 
1) 

Push the clamping pedal all the way down to ensure that the jaws on the turntable do not open unexpectedly. 

2) 

Connect the inflation gun, if it is to be installed, to its connector. 

3) 

Connect the tire changer to a compressed air network (suggested working pressure from 8bar) using the connector. Use a compressed air 
hose with on inside diameter of 7~8 mm. 

5-3 Electric link up  
1) 

Before making any electric link up, check to be certain that the main voltage corresponds to what is stamped on the voltage tag. 

2) 

It is absolutely essential that the system is equipped with a good grounding circuit. 

3) 

The machine must be connected to a power supply line circuit bracket set for 30mA  

(6) Assembly procedure 

Содержание TWC-512RMB



















Отзывы:

Похожие инструкции для TWC-512RMB