Lattice Semiconductor CertusPro-NX Скачать руководство пользователя страница 37

Страница: 37 / 171

CertusPro-NX SerDes/PCS Usage Guide

Preliminary

Technical Note

FPGA-TN-02245-0.81

Port Name

I/O

Width

Description

1’b1 – Data is valid.

1’b0 – Data is invalid.

De-asserted only to compensate for 128b130b encoding.

pipe_rx_start_block_LL_o

Out

PIPE Rx start block.

1’b1 – Start of the block.

1’b0 – Any occurrence other than the start of the block.

All blocks received are 128-bit, except SKP OS, size of which is a
variable.

pipe_rx_sync_header_LL_o

Out

2*NL

PIPE Rx sync header.
When pipe_rx_start_block_LL_o == 1’b1, it indicates the block
type:

2’b01 – Ordered set.

2’b10 – Data.

pipe_rx_data_LL_o

Out

32*NL

PIPE Rx data.

pipe_rx_datak_LL_o

Out

4*NL

PIPE Rx data K indicator for 8b10b.

pipe_rx_valid_LL_o

Out

1’b1 – PHY is locked to Rx data stream and data is valid, use
pipe_rx_data_LL_o.

1’b0 – PHY is not locked, ignore pipe_rx_data_LL_o.

pipe_rx_status_LL_o

Out

3*NL

PIPE Rx status.

3’b000 – Reserved.

3’b001 – SKP added.

3’b010 – SKP deleted.

3’b011 – Receiver detected.

3’b100 – Encoding error.

3’b111 – Disparity error.

3’b101 – Overflow error.

3’b110 – Underflow error.

pipe_usr_clk_LL_o

Out

PIPE clock connected to the hard PCIe Link Layer Quad.

LMMI Interface

LMMI is simple memory mapped interface proposed by Lattice, and is mainly used for register access.

Table 5.10

shows

the detailed LMMI interface descriptions. All these signals are per lane, and NL means the number of lanes.

Table 5.10. LMMI Interface

Port Name

I/O

Width

Description

lmmi_clk_i

LMMI clock input.

lmmi_resetn_i

Active low LMMI reset.

lmmi_request_i

Start transaction.

lmmi_wr_rdn_i

Write = HIGH, Read = LOW

lmmi_offset_i

9*NL

Address/Offset, the highest bit is used to select register space.

1’b1 – MPCS register space.

1’b0 – PMA register space.

lmmi_wdata_i

8*NL

Write data.

lmmi_rdata_valid_o

Out

Valid data indicator.

lmmi_ready_o

Out

Slave ready signal.

lmmi_rdata_o

Out

8*NL

Read data.

lmmi_addr_i

9*NL

Address bits.

Содержание CertusPro-NX












































































































































































Результаты поиска

Содержание CertusPro-NX

Отзывы:

Похожие инструкции для CertusPro-NX

Бренды по названию

Популярные бренды

Lattice Semiconductor CertusPro-NX, Руководство по эксплуатации

Результаты поиска

Содержание CertusPro-NX

Отзывы:

Похожие инструкции для CertusPro-NX

Бренды по названию

Популярные бренды