Lattice Semiconductor CertusPro-NX Скачать руководство пользователя страница 122

Страница: 122 / 171

CertusPro-NX SerDes/PCS Usage Guide

Preliminary

Technical Note

122

FPGA-TN-02245-0.81

Appendix A. Configuration Registers

A.1. PMA Registers

A.1.1. Register Address

Table A. 1. Register Address

Offset
LMMI

Register Name

Access
Type

Description

8’d0

reg00

Control register 0.

8’d1

reg01

Clock count for error counter decrement.

8’d2

reg02

Error counter threshold – Rx idle detect maximum latency.

8’d3

reg03

Rx Impedance ratio.

8’d4

reg04

Tx PLL F settings and PCLK ratio.

8’d5

reg05

Tx PLL M & N settings.

8’d6

reg06

Rx PLL F settings and PCLK ratio.

8’d7

reg07

Rx PLL M & N settings.

8’d8

reg08

250 ns timer base count.

8’d9

reg09

Tx Impedance ratio.

8’d10

reg0a

Tx Post-Cursor ratio.

8’d11

reg0b

Tx Pre-Cursor ratio.

8’d14

reg0e

Power down feature.

8’d25

reg18

Tx Amplitude ratio.

8’d33

reg21

CDR PLL frequency comparator maximum difference.

8’d34

reg22

CDR PLL frequency comparator counter.

8’d35

reg23

EI4 mode register.

8’d48

reg30

PMA Controller status.

8’d100

reg64

PRBS control register.

8’d101

reg65

PRBS error counter register.

8’d102

reg66

PHY reset override register.

8’d103

reg67

PHY power override register.

8’d116

reg68

PCS Loopback control.

8’d117

reg69

Transmit PLL Current Charge Pump.

8’d118

reg6a

Receive PLL Current Charge Pump.

8’d121

reg79

CDR PLL manual control.

8’d127

reg7f

PMA Status.

8’d128

reg80

Update settings command register.

A.1.2. Register Description

Table A. 2. Control Register 0 [reg00]

Field

Name

Access

Width

Reset

Description

[7]

auto shift

1’b1

Defines whether or not Electrical Idle 1 pattern is
automatically shifted in SerDes macro after loading the
drive pattern.

1’b1 – automatically shifted.

1’b0 – not automatically shifted.

[6]

force Rx detect

1’b0

Force the result of PCIe receiver detect operation to be

Содержание CertusPro-NX












































































































































































Результаты поиска

Содержание CertusPro-NX

Отзывы:

Похожие инструкции для CertusPro-NX

Бренды по названию

Популярные бренды

Lattice Semiconductor CertusPro-NX, Руководство по эксплуатации

Результаты поиска

Содержание CertusPro-NX

Отзывы:

Похожие инструкции для CertusPro-NX

Бренды по названию

Популярные бренды