Lattice Semiconductor CertusPro-NX Скачать руководство пользователя страница 28 | Manualshive

Страница: 28 / 171

background image

CertusPro-NX SerDes/PCS Usage Guide

Preliminary

Technical Note

28

© 2020-2021 Lattice Semiconductor

FPGA-TN-02245-0.81

All rights reserved. CONFIDENTIAL

Port Name

I/O

Width

Description

Tx/Rx FIFO Signals
mpcs_tx_ch_din_i

In

80*NL

For the signal mapping of this port, refer to

mpcs_tx_fifo_st_o

Out

4*NL

For the signal mapping of this port, refer to

mpcs_rx_ch_dout_o

Out

80*NL

For the signal mapping of this port, refer to

mpcs_rx_fifo_st_o

Out

4*NL

For the signal mapping of this port, refer to

Elastic Buffer Signals (8B/10B PCS)

mpcs_ebuf_empty_o

Out

NL

Elastic Buffer Empty output port.

1’b1 – the frequency compensation buffer, Elastic Buffer, is
empty.

1’b0 – the frequency compensation buffer, Elastic Buffer, is
not empty.

mpcs_ebuf_full_o

Out

NL

Elastic Buffer Full output port.

1’b1 – the frequency compensation buffer, Elastic Buffer, is
full.

1’b0 – the frequency compensation buffer, Elastic Buffer, is
not full.

mpcs_anxmit_i

In

NL

In GigE application case, the high level of this signal indicates
the current state is GigE Auto-negotiation. In this state, replace
/C1/, /C2/ with /I2/ ordered sets periodically so that the
following stage (CTC) gets opportunity to perform clock
frequency compensation.

Word Aligner Signals (8B/10B PCS)
mpcs_walign_en_i

In

NL

Word alignment enabling input port. This function is useful, if
the automatic synchronization is not enabled. The rising edge of
this signal triggers the word alignment operation.

mpcs_get_lsync_o

Out

NL

Link Synchronization output port.

1’b1 – link synchronization is acquired.

1’b0 – loss of link synchronization.

Lane-to-Lane Deskew Signals (8B/10B PCS)
mpcs_rx_get_lalign_o

Out

NL

Receive Lane align output port.

1’b1 – alignment acquired.

1’b0 – loss of alignment.

mpcs_rx_deskew_en_i

In

NL

Receive Deskew enable port. The rising edge of this signal
triggers the lane-to-lane deskew operation.

BER Monitor (64B/66B PCS)
mpcs_rx_hi_ber_o

Out

NL

The high level of this signal indicates the high bit error ratio is
indicated.

Block Aligner (64B/66B PCS)
mpcs_rx_blk_lock_o

Out

NL

The high level of this signal indicates the block lock is achieved.

PMA Control and Status Signals
mpcs_pwrdn_i

In

2*NL

This signal is used to put PMA in powerdown mode. This signal
has only three states. This signal is required to be clocked on
mpcs_clkin_i.

2’b11 – deep low-power state.

2’b10 – low-power state.

2’b00 – operational state.

mpcs_txhiz_i

In

NL

This signal is used to load Electrical Idle III in the Tx driver of the
PMA macro.

mpcs_rxidle_o

Out

NL

This port is used to signal the Electrical Idle condition detected
by the PMA control logic. This signal is driven by mpcs_clkin_i.

mpcs_rxerr_i

In

NL

This signal is used to report to PMA control logic that error data
is detected by the PCS logic. Asserting this signal leads CDR PLL

«
...
26
27
28
29
30
...
»

Содержание CertusPro-NX












































































































































































Отзывы:

Нет отзывов

Похожие инструкции для CertusPro-NX

Бренд: Abus Страницы: 60

Бренд: Observint Страницы: 117

Бренд: Yamaha Страницы: 6

Бренд: Yamaha Страницы: 4

Бренд: Yamaha Страницы: 22

Бренд: Yamaha Страницы: 49

Бренд: Compaq Страницы: 112

Бренд: HARTING Страницы: 13

PoleVault System A/V Source Inputs

Бренд: Extron electronics Страницы: 4

Бренд: Tektronix Страницы: 178

Бренд: CNC4PC Страницы: 11

Бренд: Freescale Semiconductor Страницы: 8

NVRx-7300 series

Бренд: Swann Страницы: 9

DVI-Vision-IP-Fiber

Бренд: G&D Страницы: 240

Бренд: ExtraHop Страницы: 2

Бренд: Wistron NeWeb Страницы: 32

Fibe-Air IP-10G

Бренд: Ceragon Страницы: 71

Бренд: Enterasys Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды