background image

Notice

This document and its contents are the intellectual property of Laserglow.com Limited (hereafter referred to as 
"Laserglow") and are intended for use only by Laserglow customers for the purpose of operating their Laserglow products. 
Unauthorized reproduction or distribution is prohibited without express written consent from Laserglow. An exception is 
granted for personal archival copies, distribution within an organization which is itself a customer of Laserglow or 
transferring this document to a new owner upon sale of the product. Careful and reasonable efforts have been made to 
ensure the quality and accuracy of this document, but Laserglow shall not be liable for errors or omissions contained 
herein, or for any incidental or consequential damages arising from the use of this document or the product itself. Safety 
information provided in this document is for reference only and should not be considered an adequate substitute for 
industry-standard laser safety training. Laserglow recommends that the Customer consult with a Certified Laser Safety 
Officer before using any type of laser device for any application. Failure to heed the recommendations, warnings, and 
safety information provided herein may result in property damage, serious injury, or death. Please read this entire 
document before attempting to operate the product and always store these instructions with the product.

Introduction

Thank you for purchasing the Virtualine™ LED SWITCH light fixture from Laserglow. This fixture is designed to provide a 
bright and highly visible line for hazard awareness and a wide range of other industrial and commercial applications. This 
manual contains complete instructions on how to set up and operate your Virtualine™ LED SWITCH, descriptions of all 
features, and some troubleshooting tips. If after reading this manual you still have questions about the safe and proper 
operation of your projector, please contact us and we would be happy to assist you. Our contact information is listed at the 
bottom of this page. 

laserglow.com/industrial

VirtuaLine™ SWITCH LED Line Projector

Содержание VirtuaLine SWITCH LED














Отзывы: