background image

 

6

 

IMPORTANT READ 

FIRST 

IMPORTANT

 

CAUTION 

KEEP FLOOR IN FRONT OF EQUIPMENT CLEAN AND DRY.  IF SPILLS 
OCCUR, CLEAN IMMEDIATELY, TO AVOID THE DANGER OF SLIPS OR 
FALLS. 

 

NOTICE 

Once the griddle temperature set point has been changed, it will heat to 
that setting each time the griddle is turned on. Refer to “Changing the 
Griddle Temperature. 

 

NOTICE 

In order for the Day Part feature to work properly, you must set up at least 
two day parts. If only one day part is set, the control will use this setting as 
the default temperature setting.   

 

WARNING 

KEEP WATER AND SOLUTIONS OUT OF CONTROLS.  NEVER SPRAY OR 
HOSE CONTROL CONSOLE. 

 

CAUTION 

MOST CLEANERS ARE HARMFUL TO THE SKIN, EYES, MUCOUS 
MEMBRANES AND CLOTHING.  PRECAUTIONS SHOULD BE TAKEN TO 
WEAR RUBBER GLOVES, GOGGLES OR FACE SHIELD AND PROTECTIVE 
CLOTHING.  CAREFULLY READ THE WARNING AND FOLLOW THE 
DIRECTIONS ON THE LABEL OF THE CLEANER TO BE USED. 

 

NOTICE 

Never leave a chlorine sanitizer in contact with stainless steel surfaces 
longer than 10 minutes.  Longer contact can cause corrosion. 

 

NOTICE 

Service on this or any other Lang Manufacturing appliance must be 
performed by qualified personnel only. Consult your authorized service 
agent directory or call the factory at 1-800-807-9054, or visit our website at 

WWW.STAR-MFG.COM

  For the service agent nearest you. 

 

WARNING 

HIGH VOLTAGE IS PRESENT INSIDE THIS APPLIANCE WHEN THE UNIT IS 
PLUGGED / WIRED INTO A LIVE RECEPTACLE.  BEFORE REPLACING 
ANY PARTS, DISCONNECT THE UNIT FROM THE ELECTRIC POWER 
SUPPLY. 

 

CAUTION 

USE OF ANY REPLACEMENT PARTS OTHER THAN THOSE SUPPLIED BY 
LANG OR THEIR AUTHORIZED DISTRIBUTORS CAN CAUSE BODILY 
INJURY TO THE OPERATOR AND DAMAGE TO THE EQUIPMENT AND 
WILL VOID ALL WARRANTIES. 

 

IMPORTANT 
The installation of the Appliance should conform to the NATIONAL FUEL GAS CODE 
"ANSI Z223.1/NFPA 54 - LATEST EDITION" AND ALL LOCAL GAS COMPANY RULES 
AND REGULATIONS.  IN CANADA INSTALLATION SHALL BE IN ACCORDANCE WITH 
THE CURRENT CAN/CGA-B149.1 NATURAL GAS INSTALLATION CODE OR 
CAN/CGA-B149.2 PROPANE INSTALLATION CODE AND LOCAL CODES WHERE 
APPLICABLE.

 

 

Содержание 224Z





























Отзывы: