background image

 

Star Manufacturing International 

10 Sunnen Drive 

St. Louis, MO.63143-3800 

Part Number: 2M-W359 

Ph: 314-781-2777 Fax: 314-781-2714 

 

Rev. C 

WWW.STAR-MFG.COM

  

October 29, 2007 

2

 

Safety 

CAUTION:

 

THE GRIDDLE IS EXTREMELY HEAVY. FOR SAFE 
HANDLING, INSTALLER SHOULD OBTAIN HELP AS 
NEEDED, OR EMPLOY APPROPRIATE MATERIALS 
HANDLING EQUIPMENT (SUCH AS A FORKLIFT, 
DOLLY, OR PALLET JACK) TO REMOVE THE UNIT 
FROM THE SKID AND MOVE IT TO THE PLACE OF 
INSTALLATION.

 

CAUTION:

 

ANY STAND, COUNTER OR OTHER DEVICE ON 
WHICH GRIDDLE WILL BE LOCATED MUST BE 
DESIGNED TO SUPPORT THE WEIGHT OF THE 
GRIDDLE. 

CAUTION:

 

SHIPPING STRAPS ARE UNDER TENSION AND CAN 
SNAP BACK WHEN CUT. 

DANGER:

 

THIS APPLIANCE MUST BE GROUNDED AT THE 
TERMINAL PROVIDED.  FAILURE TO GROUND THE 
APPLIANCE COULD RESULT IN ELECTROCUTION 
AND DEATH. 

WARNING:

 

INSTALLATION OF THE UNIT MUST BE DONE BY 
PERSONNEL QUALIFIED TO WORK WITH 
ELECTRICITY.  IMPROPER INSTALLATION CAN 
CAUSE INJURY TO PERSONNEL AND/OR DAMAGE 
TO EQUIPMENT.  UNIT MUST BE INSTALLED IN 
ACCORDANCE WITH ALL APPLICABLE CODES. 

NOTICE: 

The data plate is on top of the control box. The 
griddle voltage, wattage, serial number, wire size, 
and clearance specifications are on the data plate.  
This information should be carefully read and 
understood before proceeding with the installation. 

NOTICE:

 

The installation of any components such as a vent 
hood, grease extractors, fire extinguisher systems, 
must conform to their applicable National, State and 
locally recognized installation standards. 

NOTICE:

 

During the first few hours of operation you may 
notice a small amount of smoke coming off the unit, 
and a faint odor from the smoke.  This is normal for a 
new griddle and will disappear after the first few 
hours of use. 

CAUTION:

 

ALWAYS KEEP THE AREA NEAR THE APPLIANCE 
FREE FROM COMBUSTIBLE MATERIALS. 

CAUTION:

 

KEEP FLOOR IN FRONT OF EQUIPMENT CLEAN 
AND DRY.  IF SPILLS OCCUR, CLEAN IMMEDIATELY, 
TO AVOID THE DANGER OF SLIPS OR FALLS. 

 

 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 
 
 

Содержание 224Z





























Отзывы: