Landoll Coulter Chisel 2112 Скачать руководство пользователя страница 66

Страница: 66 / 108

3-28

F-1102-0721

ASSEMBLY INSTRUCTIONS

LED Light Installation

NOTE

Refer to

See Figure 3-19

for light bracket and wiring

harnesses placement.

Attach LH and RH light bracket assemblies, light
mounts, light mount plates to center frame using 1/2
x 4-1/2 bolts, 1/2 flat washers and 1/2 lock nuts

See

Figure 3-18

Attach ag flasher control module to bottom of right
tail light mount with 1/4 x 1-1/2 bolts, 1/4 lock nuts.

Attach left and right side red ag lamp, reflector
mounts to frame assembly, mount bracket using 1/2 x
10 bolts, 1/2 flat washers, 1/2 lock nuts.

Attach the ag red single LED lamps to tail light
mounts using 1/4 x 1-1/2 bolts, 1/4 lock nuts.

IMPORTANT

Make sure lights are positioned for maximum
visibility from the rear

See Figures 3-19

Install the rear harness to the rear tube of frame

See

Figures 3-18

. Connect the 3 pin ends to the red

warning lights, 2 pin ends to the amber warning lights
and connect the 6 pin connector to the ag flasher
control module.

See Figure

See Figures 3-17

for

LED harness wire designations.

Route main harness through all hose clamps/hose
loops from hitch to the rear of center frame, connect
the 4 pin end to the ag flasher control module.

Insure that the harnesses are clear of any moving
parts and secure the harnesses with tie wraps
provided.

Two 34” harnesses are provided if needed for main
harness to reach from flasher control module to the
tractor

See Figures 3-18

Install the stor-away holder to hose holder on hitch
with 1/4-20 x 3/4 hex head cap screws and hex lock
nuts

See Figures 3-7

Содержание Coulter Chisel 2112













































































































Результаты поиска

Содержание Coulter Chisel 2112

Отзывы:

Похожие инструкции для Coulter Chisel 2112

Бренды по названию

Популярные бренды

Landoll Coulter Chisel 2112, Руководство оператора

Результаты поиска

Содержание Coulter Chisel 2112

Отзывы:

Похожие инструкции для Coulter Chisel 2112

Бренды по названию

Популярные бренды