Landoll Coulter Chisel 2112 Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 108

background image

OPERATION AND MAINTENANCE

4-11

Lubrication Maintenance

1.

specifies the lubrication points and

intervals on the 2112 Coulter Chisel. Proper
maintenance of your machine will, under normal
operating conditions, help to keep it operating at or
near its peak performance for an extended period of
time. Proper maintenance is also a condition of
keeping your warranty in good status

Figure 4-10

.

2.

When lubricating the Coulter Chisel, SAE
multi-purpose EP grease, or EP grease with 3-5%
molybdenum sulfide is recommended. Wipe soil from
fittings before greasing. Replace any lost or broken
fittings immediately.

3.

Coulter gang bearings are equipped with triple-lip
seals that will let grease pass and not harm the seal.
Regular lubrication will maintain a full grease cavity
and help purge any contaminants. Grease the
bearings before long periods of storage to prevent
moisture buildup within the bearing cavity.

4.

Wheel seals and walking tandem seals, when
properly installed, will allow grease to pass without
harm to seals. Regular lubrication will extend service
life, particularly in severe operating conditions.

5.

The Coulter Chisel is equipped with
maintenance-free bearings in the lifts and leveler.
These areas require no lubrication.

«
...
95
96
97
98
99
...
»

Содержание Coulter Chisel 2112













































































































Отзывы:

Нет отзывов

Похожие инструкции для Coulter Chisel 2112

Бренд: Eclipse Combustion Страницы: 46

Бренд: Bard Страницы: 2

Бренд: SALUDA MEDICAL Страницы: 61

Бренд: Tascam Страницы: 80

Бренд: Tascam Страницы: 2

Бренд: Walker Страницы: 24

Бренд: Patlite Страницы: 28

Web Ankle Brace

Бренд: Darco Страницы: 2

Бренд: Darkly Labs Страницы: 13

Бренд: DARAY Страницы: 24

Body Armor Night Splint

Бренд: Darco Страницы: 2

Бренд: LaboGene Страницы: 59

Бренд: XDP Recreation Страницы: 40

Бренд: K-SPORT Страницы: 5

Бренд: PARAMOUNT BED Страницы: 28

Бренд: FOAMICO Страницы: 19

Бренд: Inspire Страницы: 19

Бренд: Qtx Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды