Landoll Coulter Chisel 2112 Скачать руководство пользователя страница 102

Страница: 102 / 108

4-16

F-1102-0721

OPERATION AND MAINTENANCE

Chopper Reel Adjustments

The optional chopper reel attachment consists of a
reel assembly that operate independently from each
other.

The reel assemblies may have either a standard
spring assembly arm or spring assembly/ hydraulic
arm option.



WARNING

Reels are set to 21-1/2” from Landoll. To adjust the
reel height, loosen the locking hex nut against the
threaded spring end

See Figures 4-12

Raise or lower the reel by turning the head of the
spring bolt, and then re-tighten the locking nut
against the spring end.

Know and verify actual implement height and
width before transporting. Attachments may
increase the overall height and width of the
implement. Use caution when transporting near
power lines. Electrocution can occur without
direct contact.

Содержание Coulter Chisel 2112













































































































Результаты поиска

Содержание Coulter Chisel 2112

Отзывы:

Похожие инструкции для Coulter Chisel 2112

Бренды по названию

Популярные бренды

Landoll Coulter Chisel 2112, Руководство оператора

Результаты поиска

Содержание Coulter Chisel 2112

Отзывы:

Похожие инструкции для Coulter Chisel 2112

Бренды по названию

Популярные бренды