Landis+Gyr E470 Series Скачать руководство пользователя страница 15

Страница: 15 / 69

Meter Operation

Issue: 1.8

Page 15 of 69

E470 Tokenless Smart Prepayment Meter



Visually display a tamper detection message; see Meter Display

section.



If the meter is on supply; the opening of the SIM flap may be

reported to the utilities information system by instantly sending an

SMS message.



Optionally the meter may be configured to open the main

contactor.

Resetting of the tamper flag/supply reconnection can be achieved by

system command or using the meter optical port.

4.5 Normal SIM Card Removal

In normal operation the SIM card may be ‘hot’ swapped by the utility

without disconnecting the supply to the meter and the customer. Upon

opening the main SIM flap the meter may send a tamper message as

described in Tamper detection (if configured); following the sending of the

message the meter will power down the SIM ready for removal. The meter

indicates that the SIM may be removed by flashing the signal strength

symbols on the display. Upon replacement of the SIM and closure of SIM

flap the meter will reenergise the device and the meter will send the new

SIM number to the utilities information system. The message will consist of

Meter serial number, SIM number and MPAN.

4.6 Operational modes

The E470 meter can be configured to operate in several different

operational modes that can be implemented remotely. The following section

details the operational modes that are supported by the meter.

4.6.1 Credit mode

The meter can be configured to operate in credit mode. In this mode of

operation the meter will not open the contactor (unless instructed) and will

ignore any credit values sent to the meter. When in credit mode the default

operating meter display is the active register display.

4.6.2 Prepayment mode

The meter can be configured to operate in prepayment mode. In this mode

of operation the meter will open the contactor when the credit value in the

meter falls below a zero value. To close the contactor the meter requires a

payment to be made to suffice any negative balance registered on the

meter. When in prepayment mode the default operating meter display is the

remaining credit display.

4.6.3 Single wallet mode

The meter can be configured to operate in a single wallet mode. In this

mode of operation the meter will use the value of credit held in the present

balance register for collection of both gas and electricity usage. The

electricity meter reduces the present balance for gas usage on receipt of

each ½ hour message from the gas meter using the gas cost today data.

Содержание E470 Series






































































Результаты поиска

Содержание E470 Series

Отзывы:

Бренды по названию

Популярные бренды

Landis+Gyr E470 Series, Руководство пользователя

Результаты поиска

Содержание E470 Series

Отзывы:

Бренды по названию

Популярные бренды