manualshive.com logo in svg
background image

LANDA VHP  •  8.913-949.0   •  Rev. 5/13

3

 

 

PRESSURE W

ASHER

 

OPERA

TOR’S MANU

AL
  

InTroDuCTIon & ImporTanT safeTy InformaTIon

Thank you for purchasing this Pressure Washer.
We reserve the right to make changes at any time 
without incurring any obligation.

owner/user responsibility:

The owner and/or user must have an understanding of 
the manufacturer’s operating instructions and warnings 
before using this pressure washer. Warning information 
should be emphasized and understood. If the operator 
is not fluent in English, the manufacturer’s instructions 
and warnings shall be read to and discussed with 
the operator in the operator’s native language by the 
purchaser/owner, making sure that the operator com-
prehends its contents.
Owner and/or user must study and maintain for future 
reference the manufacturers’ instructions.
The operator must know how to stop the machine 
quickly and understand the operation of all controls. 
Never permit anyone to operate the engine without 
proper instructions.

save These InsTruCTIons
This manual should be considered a permanent 
part of the machine and should remain with it if 
machine is resold.
When ordering parts, please specify model and 
serial number. use only identical replacement parts.
This machine is to be used only by trained operators.

ImporTanT safeTy 

InformaTIon

reaD operaTor’s 

manual Thoroughly 

prIor To use.

WARNING: To reduce the risk of 

injury, read operating instruc-
tions carefully before using.

  1.  Read the owner's manual 

thoroughly. Failure to follow 
instructions could cause mal-
function of the machine and 
result in death, serious bodily 
injury and/or property dam-
age.

  2.  Know how to stop the machine and bleed pressure 

quickly. Be thoroughly familiar with the controls.

  3.  Stay alert — watch what you are doing.
  4.  Do not replace LP tank while machine is running.
  5.  All installations must comply with local codes. Con-

tact your electrician, plumber, utility company or the 
selling distributor for specific details. If your machine 
is rated 250 volts or less, single phase will be pro-
vided with a ground fault circuit interrupter (GFCI). 
If rated more than 250 volts, or more than single 
phase this product should only be connected to a 
power supply receptacle protected by a GFCI.

DANGER: Improper connection of the equipment-
grounding conductor can result in a risk of elec-
trocution. Check with a qualified electrician or 
service personnel if you are in doubt as to whether 
the outlet is properly grounded. Do not modify the 
plug provided with the product - if it will not fit the 
outlet, have a proper outlet installed by a qualified 
electrician. Do not use any type of adaptor with 
this product.

WARNING

keep WaTer 

spray aWay from 

eleCTrICal WIrIng.

WARNING: Keep wand, hose, and 

water spray away from electric 
wiring or fatal electric shock may 
result.

6.  To protect the operator from  
 

electrical shock, the machine  

 

must be electrically grounded.  

 

It is the responsibility of the  

 

owner to connect this machine 

to a UL grounded receptacle of proper voltage and 
amperage ratings. Do not spray water on or near 
electrical components. Do not touch machine with 
wet hands or while standing in water. Always dis-
connect power before servicing.

rIsk of explosIon:  

If gas smell 

presenT Turn off 

supply

WARNING

WARNING: Flammable liquids 

can create fumes which can ig-
nite, causing property damage 
or severe injury.
WARNING: Risk of explosion — 
Operate only where open flame 
or torch is permitted.

 

 

rIsk of fIre.  

Do noT aDD fuel 

When operaTIng 

maChIne.

WARNING

WARNING: Risk of fire — Do not 

change tanks  when the product 
is operating or still hot. 
WARNING: Use vapor fuel only.

 7.  Oil burning appliances shall 

be installed only in locations 
where combustible dusts and 
flammable gases or vapors

 

 

are not present. Do not store 

or use gasoline near this machine.

    8.  Keep operating area clear of all persons.

WARNING

use proTeCTIve  

eye Wear 

anD CloThIng  

When operaTIng 

ThIs equIpmenT.

WARNING: High pressure spray 

can cause paint chips or other 
particles to become airborne 
and fly at high speeds. To avoid 
personal injury, eye, hand and 
foot safety devices must be 
worn.

9.    Eye, hand, and foot protection 

must be worn when using this 
equipment.

Содержание vhp2-1500







































Отзывы: