background image

28

SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M

1/15/21

Table of Contents

Section 5: Maintenance & Lubrication 

Maintenance

Proper servicing and adjustment is key to the long life of 

any implement. With careful inspection and routine 

maintenance, you can avoid costly downtime and repair.
Check all bolts after using unit for several hours to be 

sure they are tight. Replace any worn, damaged, or 

illegible safety labels by obtaining new labels from your 

Land Pride dealer.
The parts on your cutter have been specially designed 

and should only be replaced with genuine Land Pride 

parts. Do not alter the cutter in a way which will adversely 

affect its performance.

Cutter Blade Maintenance

DANGER

!

Always secure cutter deck in the up position with solid 

supports before servicing underside of cutter. Never work 

under equipment supported by hydraulics. Hydraulics can 

drop equipment if controls are actuated or if hydraulic lines 

burst. Either situation can drop the cutter instantly even when 

power to the hydraulics is shut off.

WARNING

!

Before cleaning and/or servicing the Rotary Cutter, disengage 

hydraulics, lower unit until resting on the ground, set park 

brake, properly shut down skid steer (see skid steer Operator’s 

Manual for shut-down instructions), shut engine off, relieve 

hydraulic pressure to the attached implement remove switch 

key, and wait for rotating parts to come to a complete stop 

before dismounting from skid steer.

WARNING

!

Keep blade bolt access hole covered at all times except when 

servicing cutter blades. Make sure driveline is disconnected 

from the tractor before servicing cutter blades. 

WARNING

!

Do not operate cutter with blades that are out-of-balance, 

bent, excessively worn, excessively nicked, or with blade bolts 

that are excessively worn. Such blades can break loose from 

the cutter at high speeds causing serious injury or death.

Always inspect cutting blades before each use. Make 

certain they are properly installed and are in good 

working condition. Replace any blade that is damaged, 

worn, bent, or excessively nicked. Never try to straighten 

a bent blade! Small nicks can be ground out when 

sharpening. 

IMPORTANT: 

Replace cutting blades with genuine 

Land Pride blades only. Blades must be replaced in 

mating pairs. Not replacing both blades will result in 

an out-of-balance condition that could contribute to 

premature bearing wear/breakage and/or structural 

cracks in gearbox and/or deck.

Remove cutting blades and sharpen or replace as 

follows:
1. Place Skid Steer in park and/or set brakes, shut 

engine off and remove ignition key.

2. Always disconnect hydraulics from Skid Steer and 

secure cutter deck in the up position with solid 

supports before servicing underside of cutter.

3.

Refer to Figure 5-1:

 Remove access blade bolt 

cover.

4.

Refer to

 

Figure 5-2:

 Rotate blade bolt (#1) until in 

alignment with access hole.

5. Unscrew locknut (#5) to remove cutting blade (#2). 

Blade bolt (#1) is keyed and will not turn freely.

6. Both blades should be sharpened at the same angle 

as the original cutting edge and must be replaced or 

re-ground at the same time to maintain proper 

balance in the cutting unit. The following precautions 

should be taken when sharpening blades:
a. Do not remove more material than necessary. 
b. Do not heat and pound out a cutting edge. 
c. Do not grind blades to a razor edge. Leave a blunt 

cutting edge approximately 1/16" thick.

d. Always grind cutting edge so end of blade remains 

square to cutting edge and not rounded.

e. Do not sharpen back side of blade.
f. Both blades should weigh the same with not more 

than 1 1/2 oz. difference. Unbalanced blades will 

cause excessive vibration which can damage 

gearbox bearings and create structural cracks.

7.

Refer to

 

Figure 5-1:

 Carefully check cutting edges of 

blades in relation to blade carrier rotation to ensure 

correct blade placement. Blade rotation is clockwise 

with cutting edge leading. Airfoil (lift) must be 

oriented toward the top of the deck.

Blade Rotation & Blade Bolt Access Cover Location

Figure 5-1

37920

Clockwise 

Blade Rotation

Blade Bolt 

Access Cover

Blade Rotation 

Decal 848-416C

Section 5: Maintenance & Lubrication

Содержание SC2560













































Отзывы: