Land Pride SC2560 Скачать руководство пользователя

Страница: 32 / 44

SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M

1/15/21

Table of Contents

Section 5: Maintenance & Lubrication

Maintenance

Proper servicing and adjustment is key to the long life of

any implement. With careful inspection and routine

maintenance, you can avoid costly downtime and repair.
Check all bolts after using unit for several hours to be

sure they are tight. Replace any worn, damaged, or

illegible safety labels by obtaining new labels from your

Land Pride dealer.
The parts on your cutter have been specially designed

and should only be replaced with genuine Land Pride

parts. Do not alter the cutter in a way which will adversely

affect its performance.

Cutter Blade Maintenance

DANGER

Always secure cutter deck in the up position with solid

supports before servicing underside of cutter. Never work

under equipment supported by hydraulics. Hydraulics can

drop equipment if controls are actuated or if hydraulic lines

burst. Either situation can drop the cutter instantly even when

power to the hydraulics is shut off.

WARNING

Before cleaning and/or servicing the Rotary Cutter, disengage

hydraulics, lower unit until resting on the ground, set park

brake, properly shut down skid steer (see skid steer Operator’s

Manual for shut-down instructions), shut engine off, relieve

hydraulic pressure to the attached implement remove switch

key, and wait for rotating parts to come to a complete stop

before dismounting from skid steer.

WARNING

Keep blade bolt access hole covered at all times except when

servicing cutter blades. Make sure driveline is disconnected

from the tractor before servicing cutter blades.

WARNING

Do not operate cutter with blades that are out-of-balance,

bent, excessively worn, excessively nicked, or with blade bolts

that are excessively worn. Such blades can break loose from

the cutter at high speeds causing serious injury or death.

Always inspect cutting blades before each use. Make

certain they are properly installed and are in good

working condition. Replace any blade that is damaged,

worn, bent, or excessively nicked. Never try to straighten

a bent blade! Small nicks can be ground out when

sharpening.

IMPORTANT:

Replace cutting blades with genuine

Land Pride blades only. Blades must be replaced in

mating pairs. Not replacing both blades will result in

an out-of-balance condition that could contribute to

premature bearing wear/breakage and/or structural

cracks in gearbox and/or deck.

Remove cutting blades and sharpen or replace as

follows:
1. Place Skid Steer in park and/or set brakes, shut

engine off and remove ignition key.

2. Always disconnect hydraulics from Skid Steer and

secure cutter deck in the up position with solid

supports before servicing underside of cutter.

Refer to Figure 5-1:

Remove access blade bolt

cover.

Refer to

Figure 5-2:

Rotate blade bolt (#1) until in

alignment with access hole.

5. Unscrew locknut (#5) to remove cutting blade (#2).

Blade bolt (#1) is keyed and will not turn freely.

6. Both blades should be sharpened at the same angle

as the original cutting edge and must be replaced or

re-ground at the same time to maintain proper

balance in the cutting unit. The following precautions

should be taken when sharpening blades:
a. Do not remove more material than necessary.
b. Do not heat and pound out a cutting edge.
c. Do not grind blades to a razor edge. Leave a blunt

cutting edge approximately 1/16" thick.

d. Always grind cutting edge so end of blade remains

square to cutting edge and not rounded.

e. Do not sharpen back side of blade.
f. Both blades should weigh the same with not more

than 1 1/2 oz. difference. Unbalanced blades will

cause excessive vibration which can damage

gearbox bearings and create structural cracks.

Refer to

Figure 5-1:

Carefully check cutting edges of

blades in relation to blade carrier rotation to ensure

correct blade placement. Blade rotation is clockwise

with cutting edge leading. Airfoil (lift) must be

oriented toward the top of the deck.

Blade Rotation & Blade Bolt Access Cover Location

Figure 5-1

37920

Clockwise

Blade Rotation

Blade Bolt

Access Cover

Blade Rotation

Decal 848-416C

Section 5: Maintenance & Lubrication

Содержание SC2560













































Результаты поиска

Содержание SC2560

Отзывы:

Похожие инструкции для SC2560

Бренды по названию

Популярные бренды

Land Pride SC2560, Руководство оператора

Результаты поиска

Содержание SC2560

Отзывы:

Похожие инструкции для SC2560

Бренды по названию

Популярные бренды