Land Pride SC2560 Скачать руководство пользователя

Страница: 34 / 44

SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M

1/15/21

Table of Contents

Section 5: Maintenance & Lubrication

Skid Shoe Replacement

Figure 5-3

Hydraulic Maintenance

DANGER

Hydraulic fluid under high pressure can penetrate skin. Wear

protective gloves and safety glasses or goggles when working

with hydraulic systems. Use a piece of cardboard or wood

rather than hands when searching for hydraulic leaks. If

hydraulic fluid is injected into the skin or eyes, it must be

treated by a doctor familiar with this type of injury within a

few hours or gangrene may result. DO NOT DELAY.

One of the most important things you can do to prevent

hydraulic system problems is to ensure that your Skid

Steer reservoir remains free of dirt and contamination.
Use a clean cloth to wipe the hose ends before attaching

them to your Skid Steer. Replace the filter element for

your Skid Steer’s hydraulic system at the prescribed

intervals. These simple maintenances will go a long way

to prevent occurrence of hydraulic problems.

37927

Long Term Storage

DANGER

Do not modify the Rotary Cutter without authorization from

Land Pride. Unauthorized modifications to the cutter can

result in the cutter not performing properly and/or cause

serious injury or death.

DANGER

Always secure cutter deck in the up position with solid

supports before servicing underside of cutter. Never work

under equipment supported by hydraulics. Hydraulics can

drop equipment if controls are actuated or if hydraulic lines

burst. Either situation can drop the cutter instantly even when

power to the hydraulics is shut off.

CAUTION

Always store cutter with hitch plate in the upright position. A

hitch plate that is stored folded down against the deck can tip

up easily resulting in serious injury to the body.

Clean the Rotary Cutter at the end of the working season

or when the cutter will not be used for a long period.
1. Clean off any dirt or grease that may have

accumulated on the cutter and moving parts. Scrape

off compacted dirt from the bottom of the deck and

then wash the surface thoroughly with a garden hose.

A coating of oil may also be applied to the lower deck

area to minimize oxidation.

2. Check blades and blade bolts for wear and replace if

necessary. See

“Cutter Blade Maintenance”

page 28.

3. Inspect for loose, damaged, or worn parts and adjust

or replace as needed.

4. Repaint parts where paint is worn or scratched to

prevent rust. Ask your Land Pride dealer for aerosol

touch-up paint. Paint is also available in touch-up

bottles with brush, quarts, and gallon sizes by adding

TU, QT, or GL to the end of the aerosol part number.

5. Replace all damaged or missing decals.
6. Lubricate as noted in the

Lubrication

portion of this

section starting on page 31.

7. Store the Rotary Cutter in a clean, dry place. The deck

should be positioned on a flat surface to suitable Skid

Steer hook-up height. Ensure that the main frame is

stable. Use auxiliary supports or posts if necessary to

prevent the possibility of the unit tipping over. Store

hitch in the upright position.

Land Pride Aerosol Touch-up Paint

Part No.

Part Description

821-011C

PAINT LP BEIGE AEROSOL SPRAY CAN

821-002C

PAINT GP BLACK SPRAY CAN

Содержание SC2560













































Результаты поиска

Содержание SC2560

Отзывы:

Похожие инструкции для SC2560

Бренды по названию

Популярные бренды

Land Pride SC2560, Руководство оператора

Результаты поиска

Содержание SC2560

Отзывы:

Похожие инструкции для SC2560

Бренды по названию

Популярные бренды