Land Pride SC2560 Скачать руководство пользователя | Manualshive

Страница: 39 / 44

background image

35

1/15/21

SC2560 & SC2572 Skid Steer Rotary Cutter 326-836M

Table of Contents

Section 7: Features & Benefits

SC25 Series (Skid Steer)

Features

Benefits

Low volume motor @ 11-16 gpm
Medium volume motor @ 17-21 gpm
High volume motor @ 22-27 gpm

Customer can choose one of three optional motors for the SC2560 cutter or one of
two optional motors (medium and high volume) for the SC2572 cutter. This allows
the cutter to fit a wide variety of Skid Steers. Also the deck can be upgraded to a
different motor when owner upgrades his Skid Steer.

Two year gearbox & motor warranty

Shows Land Pride’s confidence in the gearbox and motor.

Case drain

Protects gearbox.

1/4" Side panels for
overall reinforcement

Protects sides from debris being thrown against them from the blades.

Front and rear chain shields

Single chain on the front and double chain on the rear. Reduces flying debris.

Replaceable skid shoes (optional)

Protect side plate structure. Shoes are replaceable for convenience.

Splined blade bar

Allows for tight positive fit of stump jumper and blade bar to motor output shaft.

3/16" Round stump jumper

Standard stump jumper aids in sliding over obstructions, which helps protect
gearbox output shaft.

1/2" x 4" Heat-treated
free swinging blades

Heat-treated blades offer longer life.
Free swinging blades protect from obstructions.

2" Diameter cutting capacity

Can aid in clearing brush.

SC2560 High blade tip speed

11-16 gpm motor = 18,540 fpm at 16 gpm.
17-21 gpm motor = 18,850 fpm at 21 gpm.
22-27 gpm motor = 19,000 fpm at 27 gpm.

SC2572 High blade tip speed

17-21 gpm motor = 17,200 fpm at 21 gpm.
22-27 gpm motor = 18,550 fpm at 27 gpm.

Offset hitch (8 1/2" to the right)

Allows the operator to cut close to obstacles on the right side.

Optional front gauge wheel

Provides easy operation and handling over uneven terrain, laminated tire can’t go
flat.

Floating hitch mounting plate

Allows smoother travel over rough terrain with the optional gauge wheel easing the
fatigue put on the operator.

Operator protection door (optional)

Provides additional operator protection from flying objects.

Lift limit safety chain

Provides additional operator protection from flying objects by allowing the Rotary
Cutter to only be lifted up to 18".

Section 7: Features & Benefits

«
...
37
38
39
40
41
...
»

Содержание SC2560













































Отзывы:

Нет отзывов

Похожие инструкции для SC2560

Camm-1 CX-24/12

Бренд: Roland Страницы: 20

Бренд: Zenoah Страницы: 24

Бренд: Hitachi Koki Страницы: 32

Бренд: Ogura Страницы: 16

Бренд: Tar River Страницы: 36

Big Shot Pro 660550

Бренд: SIZZIX Страницы: 54

Бренд: Logan Graphic Products Страницы: 2

Бренд: Dremel Страницы: 4

Бренд: Peach Страницы: 34

Бренд: ADE Страницы: 12

Бренд: ADE Страницы: 20

Бренд: GMS Страницы: 29

Бренд: RASOR Страницы: 15

Бренд: HSGM Страницы: 8

Бренд: Hallde Страницы: 55

Бренд: Zenoah Страницы: 60

KZ-4000BC-PRO-2S

Бренд: Kasei Страницы: 36

Бренд: Garland Страницы: 144

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды