Land Pride RCF2084 Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 40

background image

Table of Contents

11/14/18

©

Copyright 2018 All rights Reserved

Land Pride provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has been taken in the
preparation of this manual, Land Pride assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use
of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this
product at the time of its publication, and may not reflect the product in the future.

Land Pride is a registered trademark.

All other brands and product names are trademarks or registered trademarks of their respective holders.

Printed in the United States of America.

RCF2084 Rotary Cutters 326-461M

Table of Contents

Important Safety Information . . . . . . . . . . . . . 1

Look For The Safety Alert Symbol   . . . . . . . . . . . . . 1
Safety at All Times   . . . . . . . . . . . . . . . . . . . . . . . . . 1
Safety Labels   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Application . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . 7

Terminology: . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Definitions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Owner Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Serial Number . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Further Assistance . . . . . . . . . . . . . . . . . . . . . . . . 7

Section 1: Assembly & Set-up . . . . . . . . . . . . 8

Tractor Requirements  . . . . . . . . . . . . . . . . . . . . . . . 8
Tractor Shutdown Procedure   . . . . . . . . . . . . . . . . . 8
Torque Requirements  . . . . . . . . . . . . . . . . . . . . . . . 8
Uncrating Instructions  . . . . . . . . . . . . . . . . . . . . . . . 8
Gearbox Vented Dipstick   . . . . . . . . . . . . . . . . . . . . 8
3-Point Hitch Assembly  . . . . . . . . . . . . . . . . . . . . . . 9
Optional Front Guards . . . . . . . . . . . . . . . . . . . . . . 10

Front Rubber Guard Assembly . . . . . . . . . . . . . . 10
Front Single Chain Guard Assembly . . . . . . . . . 10

Optional Rear Guards . . . . . . . . . . . . . . . . . . . . . . 11

Remove Rear Metal Band Deflector . . . . . . . . . . 11
Rear Single Chain Guard . . . . . . . . . . . . . . . . . . 11

Replaceable Skid Shoes (Accessory)  . . . . . . . . . . 11
Single Tailwheel Assembly  . . . . . . . . . . . . . . . . . . 12
Dual Tailwheel Assembly   . . . . . . . . . . . . . . . . . . . 12
Driveline Installation   . . . . . . . . . . . . . . . . . . . . . . . 13
Tractor Hook-Up  . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Hook-up Driveline to Tractor   . . . . . . . . . . . . . . . 15
Check Clearances  . . . . . . . . . . . . . . . . . . . . . . . 15
Check Driveline Collapsible Length  . . . . . . . . . . 15
Shorten Driveline  . . . . . . . . . . . . . . . . . . . . . . . . 16
Check Driveline Maximum Length  . . . . . . . . . . . 16
Check Driveline Interference   . . . . . . . . . . . . . . . 16

Section 2: Adjustments . . . . . . . . . . . . . . . . . 17

Deck Leveling & Cutting Height . . . . . . . . . . . . . . . 17
Deck Leveling From Left to Right   . . . . . . . . . . . . . 17
Deck Cutting Height   . . . . . . . . . . . . . . . . . . . . . . . 17
Single Tailwheel Height Adjustment   . . . . . . . . . . . 18
Dual Tailwheel Height Adjustment   . . . . . . . . . . . . 18

Tractor Center 3-Point Adjustment . . . . . . . . . . . 19

Section 3: Operating Instructions . . . . . . . . . 20

Operating Checklist  . . . . . . . . . . . . . . . . . . . . . . . . 20
Safety Information  . . . . . . . . . . . . . . . . . . . . . . . . . 20
Inspect Tractor & Cutter   . . . . . . . . . . . . . . . . . . . . 21
Transporting   . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Blade Engagement & Disengagement  . . . . . . . . . . 22

Blade Engagement . . . . . . . . . . . . . . . . . . . . . . . 22
Blade Disengagement . . . . . . . . . . . . . . . . . . . . 22

Field Operation  . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Unhooking the Rotary Cutter  . . . . . . . . . . . . . . . . . 23
General Operating Instructions  . . . . . . . . . . . . . . . 23

Section 4: Maintenance & Lubrication . . . . . 24

Maintenance  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Cutter Blade Maintenance  . . . . . . . . . . . . . . . . . . . 24
Slip-Clutch Protected Drivelines   . . . . . . . . . . . . . . 25
Clutch Run-In   . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Clutch Assembly and Disassembly  . . . . . . . . . . . . 26
Accessory Skid Shoe Maintenance  . . . . . . . . . . . . 26
Long-Term Storage  . . . . . . . . . . . . . . . . . . . . . . . . 27
Ordering Replacement Parts  . . . . . . . . . . . . . . . . . 27
Lubrication Points   . . . . . . . . . . . . . . . . . . . . . . . . . 28

Gauge Wheel Spindle Tube  . . . . . . . . . . . . . . . . 28
Gauge Wheel Hub   . . . . . . . . . . . . . . . . . . . . . . . 28
Gearbox  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Driveline U-Joints  . . . . . . . . . . . . . . . . . . . . . . . . 29
Driveline Shield Bearings  . . . . . . . . . . . . . . . . . . 29
Driveline Profiles   . . . . . . . . . . . . . . . . . . . . . . . . 29

Section 5: Specifications & Capacities  . . . . . 30
Section 6: Features & Benefits   . . . . . . . . . . . 32
Section 7: Troubleshooting  . . . . . . . . . . . . . . 33
Section 8: Torque Values Chart  . . . . . . . . . . . 34
Section 9: Warranty   . . . . . . . . . . . . . . . . . . . . 35

«
1
2
3
4
5
...
»

Содержание RCF2084









































Отзывы:

Нет отзывов

Похожие инструкции для RCF2084

Бренд: Olfa Страницы: 1

Бренд: Brush Wolf Страницы: 20

Бренд: benza Страницы: 100

Бренд: Worx Страницы: 36

Vitrex Versatile Power Max 560

Бренд: QEP Страницы: 5

Бренд: sunjoe Страницы: 16

Бренд: Agrimate Страницы: 23

Бренд: Laser Mech Страницы: 62

Бренд: Royal Catering Страницы: 11

Бренд: Hypertherm Страницы: 4

Бренд: Hypertherm Страницы: 47

Бренд: Floor Boar Страницы: 20

Бренд: Racing Страницы: 22

Бренд: UCHIDA Страницы: 58

Бренд: YATO Страницы: 116

Бренд: Saga Страницы: 31

Бренд: Land Pride Страницы: 342

Бренд: Vari Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды