Land Pride RCF2084 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 40

Land Pride RCF2084 Скачать руководство пользователя страница 13

9

Section 1: Assembly & Set-up

11/14/18

RCF2084 Rotary Cutters 326-461M

Table of Contents

5. Rotate hitch straps (#6 & #7), floating top hitch (#11),

and rear braces (#13) up until holes in rear braces
align with hole in floating top hitch (#11).

6. Insert 3/4"-10 x 4 1/2" GR5 bolt (#5) into the left rear

brace (#13), floating top hitch (#11), and right rear
brace (#13).

7.

Secure bolt (#5) with hex locknut (#12). Draw locknut
up snug and then back off 1/4 turn.

8. Attach driveline hook (#17) to hitch strap (#6) using

5/16"-18 x 1 1/4" bolt (#16) and locknut (#18). Tighten
locknut to the correct torque.

IMPORTANT:

See Detail A in Figure 1-2. Floating

top hitch (#11) must be installed with ears "A" above
rear braces (#13).

NOTE:

After assembly of hitch, push on top of

A-frame assembly (#6 & #7). It should rotate
backwards and floating top link (#11) should rotate
upwards. If they are too stiff to rotate, loosen
nuts (#12) until floating top link (#11) rotates freely.

Hitch Assembly

Figure 1-2

33132

3-Point Hitch Assembly

Refer to Figure 1-2:

1.

Assemble left-hand and right-hand hitch straps
(#6 & #7) to the inside hitch plates as shown with
5/8"-11 X 2" bolts (#1), bushings (#2), flat washers
(#3), and hex flange locknuts (#4). Tighten locknuts
to the correct torque.

2. Attach end without ears "A" of floating top

hitch (#11) between shields (#15 & #16) and hitch
straps (#6 & #7) with 3/4"-10 x 4 1/2" GR5 bolt (#8)
and locknut (#12). Draw locknut up snug and then
back off 1/4 turn.

3. Insert clevis pin (#9) through top holes in hitch straps

(#6 & #7). Secure with hairpin cotter (#10).

4. Locate 21/32" holes on end of rear braces (#13) and

attach that end to rear strap lugs with 5/8"-11 x 1 3/4"
GR5 bolts (#14) and hex flange locknuts (#15). Draw
locknuts (#15) up snug and then back off 1/4 turn.

IMPORTANT:

Be sure to mount left-hand hitch

brace (#6) and right-hand hitch brace (#7) with
stiffeners on the underside facing forward.

«
...
11
12
13
14
15
...
»

Содержание RCF2084









































Отзывы:

Нет отзывов