Land Pride RCF2084 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 40

Land Pride RCF2084 Скачать руководство пользователя страница 30

26

Section 4: Maintenance & Lubrication

RCF2084 Rotary Cutters 326-461M

11/14/18

Table of Contents

Clutch Assembly and Disassembly

Disassembly

Refer to Figure 5-3:

See

IMPORTANT NOTE

above before disassembling

clutch. After measuring and recording each spring length,
remove spring retainer nuts (#1), springs (#2), and bolts
(#3). Each friction disc (#4) must then be separated from
the metal surface adjacent to it. Refer to the Parts Manual
for a detailed parts breakdown.

Inspection

Inspect all parts for excessive wear and condition. Clean
all parts that do not require replacement.The original
friction disc thickness is 1/8" (3.2mm) and should be
replaced if thickness falls below 3/64" (1.1mm). If
clutches have been slipped to the point of “smoking”, the
friction discs may be damaged and should be replaced.
Heat build-up may also affect the yoke joints.

Assembly

Refer to Figure 5-4:

Reassemble each friction disc (#4) next to the metal plate
it was separated from. Install bolts (#3) through the end
plates and intermediate plates as shown. Place springs
(#2) over bolts (#3) and secure with nuts (#1).

Refer to Figure 5-4:

Progressively tighten each spring retainer bolt until
correct spring height “A” dimension is obtained.

Accessory Skid Shoe Maintenance

Refer to Figure 5-5:

!

WARNING

To avoid serious injury or death:
Excessive wear on skid shoes can damage side panels, cause

inadequate operation of cutter, and create a safety hazard.

Always replace skid shoes at the first sign of wearing thin.

There are skid shoes mounted on the cutter sides. Check
both skid shoes for wear and replace if necessary. Order
only genuine Land Pride parts from your local Land Pride
dealer.

1.

Remove 3/8" hex whiz nuts (#3), 3/8" plow bolts (#2)
and skid shoe (#1) as shown.

2. Plow bolts should be checked for wear and replaced

if necessary.

3. Attach new skid shoe (#1) to cutter with existing

3/8" plow bolts (#2) and secure with 3/8" hex whiz
nuts. Tighten to the correct torque.

4. Repeat on opposite side.

IMPORTANT: Refer to Figure 5-4.

measure and record length (“A”) of each clutch
spring before disassembling clutch.

Clutch Disassembly

Figure 5-3

Clutch Adjustment

Figure 5-4

Skid Shoe Replacement

Figure 5-5

Model

No.

Driveline

No.

Power

Take-Off

Speed

Ca

t

No

.

A (inches)

Spring Height

RCF2084 826-510C

540

4

1.283" (1 9/32")

33162

24600

A = Measured length of each spring
before disassembling slip clutch.

Use “A” dimension in table below
if measurements were not taken
before disassembling slip clutch.

30933

Land Pride Skid Shoe Replacement Parts

Item Part No.

Part Description

1

326-221D

SKID SHOE

2

802-603C

PLOW 3/8" - 16 x 1" GR5

3

803-198C

NUT HEX WHIZ 3/8-16 PLT

«
...
28
29
30
31
32
...
»

Содержание RCF2084









































Отзывы:

Нет отзывов