Land Pride RCF2084 Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 40

Land Pride RCF2084 Скачать руководство пользователя страница 24

20

Section 3: Operating Instructions

RCF2084 Rotary Cutters 326-461M

11/14/18

Table of Contents

Section 3:

Operating Instructions

Operating Checklist

Hazard control and accident prevention are dependent
upon awareness, concern, prudence, and proper training
involved in the operation, transport, maintenance, and
storage of the Rotary Cutter. Therefore, it is absolutely
essential that no one operates the Rotary Cutter unless
they are age 16 or older and have read, fully understood,
and are totally familiar with the Operator’s Manual. Make
sure the operator has paid particular attention to:

•

Important Safety Information

, pages 1

•

Section 1: Assembly & Set-up,

•

Section 2: Adjustments

•

Section 3: Operating Instructions

•

Section 4: Maintenance & Lubrication

Perform the following inspections before using your
Rotary Cutter.

Safety Information

!

DANGER

To avoid serious injury or death:

•

Never place hands or feet under the deck or attempt to make

adjustments to the cutter with power take-off engaged. Cutter

blades rotating at high speeds cannot be seen and are located

close to the deck sides. Body extremities will be cut off

•

Do not use cutter as a fan. Cutting blades are not properly

designed or guarded for this use.

•

Do not engage power take-off while hooking-up or

unhooking the driveline, or while someone is standing near

the driveline. A person’s body and/or clothing can become

entangled in the driveline.

•

Be sure deck is lowered to the ground and all hydraulic

pressure is relieved before disconnecting or reconnecting

hydraulic line and/or fittings between Rotary Cutter and

tractor hydraulic system.

•

All guards and shields must be installed and in good

working condition while operating the implement.

Operating Checklist



Check

Page

Make sure all guards and shields are in place.
Refer to "Important Safety Information".

1

Follow hook-up & Driveline Installation. Refer to
"Tractor Hook-Up" & "Dr iveline Installation".

Make all required adjustments.
Refer to "Section 2: Adjustments".

Preform all required maintenance. Refer to
"Section 4: Maintenance & Lubrication".

Lubricate cutter and driveline as needed.
Refer to "Lubrication Points".

Lubricate all gearboxes and replace oil plugs
properly. Refer to "Gearbox" lubrication.

Check cutter initially and periodically for loose
bolts and pins. Refer to “Torque Values Chart”.

•

Tractor power take-off shaft shield, driveline shields, and

gearbox shaft shields must be installed and in good working

condition to avoid driveline entanglement and projectiles

flying off of the driveline.

•

Rotary Cutters have the ability to discharge objects at high

speeds; therefore, the use of front and rear safety guards is

mandatory when cutting along roadways and in areas where

people may be present. Stop blade rotation if a bystander is

in or around the area.

•

Always disconnect driveline from power take-off shaft

before servicing underside of cutter. The tractor can be

started with power take-off engaged.

•

Do not use a power take-off adapter. The adapter will

increase strain on the tractor’s power take-off shaft causing

possible damage to shaft and driveline. It will also defeat

the purpose of the tractor’s power take-off shield.

!

WARNING

To avoid serious injury or death:

•

Allow only persons to operate this implement who have fully

read and comprehended this manual, who have been properly

trained in the safe operation of this implement, and who are

age 16 or older. Serious injury or death can result from the

inability to read, understand, and follow instructions

provided in this manual.

•

Perform scheduled maintenance. Check for loose hardware,

missing parts, broken parts, structural cracks, and excessive

wear. Make repairs before putting implement back into

service. Serious breakdowns can result in injury or death.

•

Never carry riders on the implement or tractor. Riders can

obstruct the operator’s view, interfere with control of the

equipment, be pinched by moving components, become

entangled in rotating components, be struck by objects, be

thrown or fall from the equipment, etc.

•

A rotating driveline must not exceed an angle of 25 degrees

up or down, and never engage a driveline while at an angle

exceeding 25 degrees up or down. The driveline can break

and send projectiles.

•

Always disengage power take-off before lifting cutter fully

up. Never operate cutter in the raised position. The cutter

can discharge objects at high speeds.

•

Select a safe ground speed when transporting. Never travel at

a speed which does not allow adequate control of steering

and stopping, and never exceed 20 mph (32.2 km/h) with

attached equipment. Rough terrain requires a slower speed.

•

Always disengage power take-off, put tractor in park or set

park brake, shut tractor engine off, remove ignition key, and

wait for blades to come to a complete stop before

dismounting tractor.

•

Do not exceed rated cutting capacity of your cutter. See

specifications & capacities for specified cutting capacity.

Exceeding rated cutting capacity can damage drive

components, cutter blades, and deck components.

«
...
22
23
24
25
26
...
»

Содержание RCF2084









































Отзывы:

Нет отзывов