Land Pride RCF2084 Скачать руководство пользователя страница 18 | Manualshive

Страница: 18 / 40

background image

14

Section 1: Assembly & Set-up

RCF2084 Rotary Cutters 326-461M

11/14/18

Table of Contents

Tractor Hook-Up

Refer to Figure 1-11:

!

DANGER

To avoid serious injury or death:
A crushing hazard exists while hooking-up and unhooking

implement. Keep people and animals away while backing-up

to implement or pulling away from implement. Do not operate

hydraulic controls while a person or animal is directly behind

the power machine or near the implement.

A tractor with 3-point Category I or II hitch is required.
The lower 3-point arms must be stabilized to prevent
side-to-side movement. Most tractors have sway blocks
or adjustable chains for this purpose.

1.

Slowly back tractor up to Rotary Cutter while using
tractor’s 3-Point hydraulic control to align lower
3-Point arm holes with clevis lug holes “C”.

2. Engage tractor park brake, shut tractor engine off,

and remove key before dismounting from tractor.

3. Attach lower arms to clevises with hitch pins (#2) and

secure with hairpin cotters (#6) as follows:

a.

Cat. l 3-Point Hitch:

Insert hairpin cotters (#6) in

hole “A”.

b.

Cat. ll 3-Point Hitch and Cat. l & ll Quick Hitch:

Insert hairpin cotters (#6) in hole “B”.

c. See also Figure 1-12 & Figure 1-13 for illustration

of hitch pin positions in clevis.

4. Connect top center 3-Point link to upper pivot hitch

holes with clevis pin (#8) and hairpin cotter (#7).

NOTE:

Land Pride’s QH15 Category I or QH20

Category II Quick Hitch can be attached to the
tractor to provide quick and easy 3-point hook-up
and detachment. See your nearest Land Pride
dealer to purchase a Quick Hitch.

5. The length of the top center link will be adjusted later.

6. The arm lift cylinders on your tractor’s 3- point hitch

should be adjusted to allow for lateral float. Please
consult your tractor’s manual for instructions.

3-Point Hitch Pin Configuration For Cat. l Hitch

Figure 1-12

3-Point Hitch Pin Configuration For Cat. ll Hitch And
Quick Hitch Pin Configuration For Cat. l & ll Hitches

Figure 1-13

Hook-up Driveline to Tractor

Refer to Figure 1-11 on page 14:

!

DANGER

To avoid serious injury or death:

•

Do not engage power take-off while hooking-up or

unhooking the driveline, or while someone is standing near

the driveline. A person’s body and/or clothing can become

entangled in the driveline.

35391

Hitch Pins

Hairpin Cotters
In Holes “A”

1-3

35391

Hairpin Cotters
In Holes “B”

Hitch Pins

1-4

Tractor Hook-up

Figure 1-11

37955

37298

«
...
16
17
18
19
20
...
»

Содержание RCF2084









































Отзывы:

Нет отзывов

Похожие инструкции для RCF2084

Бренд: Wolfcraft Страницы: 52

Бренд: Ryobi Страницы: 17

Бренд: Bushranger Страницы: 36

Бренд: Okay Страницы: 56

ClassicCut CL100

Бренд: Rexel Страницы: 30

Бренд: KEENCUT Страницы: 21

Бренд: 2M2 Страницы: 24

Бренд: Stihl Страницы: 36

Бренд: Stihl Страницы: 104

Бренд: Land Pride Страницы: 38

Sirmex SC Series

Бренд: Kapriol Страницы: 18

Бренд: Raycer Страницы: 23

Бренд: Felder Страницы: 104

Бренд: Bush Hog Страницы: 1

Бренд: Makita Страницы: 12

POWERplus POWX240

Бренд: VARO Страницы: 11

Бренд: Makita Страницы: 72

Бренд: Officezone Страницы: 1

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды